- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS2492PW (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 PDF資料下載
參數資料
| 型號： | TPS2492PW |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| 封裝： | GREEN, PLASTIC, TSSOP-14 |
| 文件頁數： | 6/33頁 |
| 文件大?。?/td> | 1096K |
| 代理商： | TPS2492PW |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
SLUSA65A – JULY 2010 – REVISED AUGUST 2010
www.ti.com
TIMER and PG Operation (Figure 13)
The TIMER pin charges CT as long as limiting action continues, and discharges at a 1/10 charge rate when
limiting stops. If the voltage on CT reaches 4 V before the output is charged, the external FET is turned off and
either a latch-off or restart cycle commences, depending on the part type. The open-drain PG output provides a
deglitched end-of-charge indication which is based on the voltage across the external FET. PG is useful for
preventing a downstream DC-to-DC converter from starting while CO is still charging. PG goes active (low) about
9 ms after CO is charged. This delay allows the external FET to fully turn on and any transients in the power
circuits to end before the converter starts up. The resistor pull-up shown on pin PG in the Typical Application
Circuit only demonstrates operation; the actual connection to the converter depends on the application. Timing
can appear to terminate early in some designs if operation transitions out of the power limit mode into a gate
charge-rate limited mode at low VDS values. This effect sometimes occurs because gate capacitances, CGD and
CGS, are nonlinear with applied voltage, getting larger at smaller voltage. This can be seen in Figure 13.
Figure 13. Basic Board Insertion
14
Copyright 2010, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2540RTER | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| TPS2540RTET | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| TPS2541RTET | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| TPS2550DBV | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2551DRVR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2492PW | 制造商:Texas Instruments 功能描述:HOT SWAP CONTROLLER IC 80V TSSOP-14 |
| TPS2492PWR | 功能描述:熱插拔功率分布 Pos Hi-Vltg Pwr-Ltd Hotswap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2493EVM-002 | 功能描述:電源管理IC開發工具 TPS2493 Hot Swap ontroller Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2493EVM-004 | 功能描述:電源管理IC開發工具 TPS2493 Hot Swap ontroller Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2493PW | 功能描述:熱插拔功率分布 Pos Hi-Vltg Pwr-Ltd Hotswap Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。