- 您現在的位置：買賣IC網 > PDF目錄98280 > TPS2557DRBT (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | TPS2557DRBT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | GREEN, PLASTIC, SON-8 |
| 文件頁數： | 2/22頁 |
| 文件大?。?/td> | 942K |
| 代理商： | TPS2557DRBT |
SLVS931 – NOVEMBER 2009
www.ti.com
FAULT RESPONSE
The FAULT open-drain output is asserted (active low) during an overcurrent or overtemperature condition. The
TPS2556/57 asserts the FAULT signal until the fault condition is removed and the device resumes normal
operation. The TPS2556/57 is designed to eliminate false FAULTreporting by using an internal delay "deglitch"
circuit for overcurrent (9-ms typ) conditions without the need for external circuitry. This ensures that FAULTis not
accidentally asserted due to normal operation such as starting into a heavy capacitive load. The deglitch circuitry
delays entering and leaving current-limit induced fault conditions. The FAULTsignal is not deglitched when the
MOSFET is disabled due to an overtemperature condition but is deglitched after the device has cooled and
begins to turn on. This unidirectional deglitch prevents FAULT oscillation during an overtemperature event.
UNDERVOLTAGE LOCKOUT (UVLO)
The undervoltage lockout (UVLO) circuit disables the power switch until the input voltage reaches the UVLO
turn-on threshold. Built-in hysteresis prevents unwanted on/off cycling due to input voltage droop during turn on.
ENABLE (EN OR EN)
The logic enable controls the power switch and device supply current. The supply current is reduced to less than
2-
μA when a logic high is present on EN or when a logic low is present on EN. A logic low input on EN or a logic
high input on EN enables the driver, control circuits, and power switch. The enable input is compatible with both
TTL and CMOS logic levels.
THERMAL SENSE
The TPS2556/57 self protects by using two independent thermal sensing circuits that monitor the operating
temperature of the power switch and disable operation if the temperature exceeds recommended operating
conditions. The TPS2556/57 device operates in constant-current mode during an overcurrent conditions, which
increases the voltage drop across power switch. The power dissipation in the package is proportional to the
voltage drop across the power switch, which increases the junction temperature during an overcurrent condition.
The first thermal sensor (OTSD) turns off the power switch when the die temperature exceeds 135°C (min) and
the part is in current limit. Hysteresis is built into the thermal sensor, and the switch turns on after the device has
cooled approximately 20 °C.
The TPS2556/57 also has a second ambient thermal sensor (OTSD2). The ambient thermal sensor turns off the
power switch when the die temperature exceeds 155°C (min) regardless of whether the power switch is in
current limit and will turn on the power switch after the device has cooled approximately 20 °C. The TPS2556/57
continues to cycle off and on until the fault is removed.
APPLICATION INFORMATION
INPUT AND OUTPUT CAPACITANCE
Input and output capacitance improves the performance of the device; the actual capacitance should be
optimized for the particular application. For all applications, a 0.1
μF or greater ceramic bypass capacitor between
IN and GND is recommended as close to the device as possible for local noise decoupling. This precaution
reduces ringing on the input due to power-supply transients. Additional input capacitance may be needed on the
input to reduce voltage overshoot from exceeding the absolute-maximum voltage of the device during heavy
transient conditions. This is especially important during bench testing when long, inductive cables are used to
connect the evaluation board to the bench power supply.
Output capacitance is not required, but placing a high-value electrolytic capacitor on the output pin is
recommended when large transient currents are expected on the output.
10
Copyright 2009, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2557DRB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2561DRC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS2561DRCT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| TPS3305-20QDRQ1 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| TPS3305-18QDRQ1 | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2557QDRBRQ1 | 功能描述:IC PWR DIST SWITCH ADJ 8SON 制造商:texas instruments 系列:汽車級，AEC-Q100 包裝:剪切帶（CT） 零件狀態:有效 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:2.5 V ~ 6.5 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:5A 導通電阻（典型值）:22 毫歐 輸入類型:非反相 特性:壓擺率受控型，狀態標志 故障保護:限流（可調），超溫，UVLO 工作溫度:-40°C ~ 125°C （TJ） 封裝/外殼:8-VDFN 裸露焊盤 供應商器件封裝:8-SON（3x3） 標準包裝:1 |
| TPS2559DRCR | 功能描述:IC PWR DIST SWITCH ADJ 10VSON 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:2.5 V ~ 6.5 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:5.5A 導通電阻（典型值）:13 毫歐 輸入類型:非反相 特性:壓擺率受控型，狀態標志 故障保護:限流（可調），超溫，UVLO 工作溫度:-40°C ~ 125°C （TJ） 封裝/外殼:10-VFDFN 裸露焊盤 供應商器件封裝:10-VSON（3x3） 標準包裝:1 |
| TPS2559DRCT | 功能描述:IC PWR DIST SWITCH ADJ 10VSON 制造商:texas instruments 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:10-VFDFN 裸露焊盤 供應商器件封裝:10-VSON（3x3） 標準包裝:1 |
| TPS2559EVM-624 | 功能描述:EVAL MODULE FOR TPS2559 制造商:texas instruments 系列:- 零件狀態:在售 主要用途:電源管理，配電開關（負載開關） 嵌入式:- 使用的 IC/零件:TPS2559 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
| TPS2559QWDRCRQ1 | 功能描述:IC DISTRIBUTION SWITCH 10VSON 制造商:texas instruments 系列:汽車級，AEC-Q100 包裝:剪切帶（CT） 零件狀態:有效 開關類型:通用 輸出數:1 比率 - 輸入:輸出:1:1 輸出配置:高端 輸出類型:N 通道 接口:開/關 電壓 - 負載:2.5 V ~ 6.5 V 電壓 - 電源（Vcc/Vdd）:不需要 電流 - 輸出（最大值）:5.5A 導通電阻（典型值）:13 毫歐 輸入類型:非反相 特性:壓擺率受控型，狀態標志 故障保護:限流（可調），超溫，反向電流，UVLO 工作溫度:-40°C ~ 125°C （TJ） 封裝/外殼:10-VFDFN 裸露焊盤 供應商器件封裝:10-VSON（3x3） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。