參數資料
型號： TPS40075RHLR
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20
封裝： PLASTIC, QFN-20
文件頁數： 16/44頁
文件大小： 806K
代理商： TPS40075RHLR
www.ti.com
GROUNDING AND BOARD LAYOUT
SYNCHRONOUS RECTIFIER CONTROL
SLUS676A – MAY 2006 – REVISED SEPTEMBER 2007
The TPS40075 provides separate signal ground (GND) and power ground (PGND) pins. Care should be given to
proper separation of the circuit grounds. Each ground should consist of a plane to minimize its impedance if
possible. The high power noisy circuits such as the output, synchronous rectifier, MOSFET driver decoupling
capacitor (DBP), and the input capacitor should be connected to PGND plane.
Sensitive nodes such as the FB resistor divider and RT should be connected to the GND plane. The GND plane
should only make a single point connection to the PGND plane. It is suggested that the GND pin be tied to the
copper area for the PowerPAD underneath the chip. Tie the PGND to the PowerPAD copper area as well and
make the connection to the power circuit ground from the PGND pin. Reference the output voltage divider to the
GND pin.
Component placement should ensure that bypass capacitors (LVPB and DBP) are located as close as possible
to their respective power and ground pins. Also, sensitive circuits such as FB, RT and ILIM should not be located
near high dv/dt nodes such as HDRV, LDRV, BOOST, and the switch node (SW). Failure to follow careful layout
practices results in sub-optimal operation.
Table 2 describes the state of the rectifier MOSFET control under various operating conditions.
Table 2. Synchronous Rectifier MOSFET States
SYNCHRONOUS RECTIFIER OPERATION DURING
FAULT
SOFT-START
NORMAL
(FAULT RECOVERY IS SAME
OVERVOLTAGE
AS SOFT-START)
Off until first high-side pulse is
Turns off at the start of a new
Turns OFF only at start of next
detected, then on when high-side
cycle. Turns on when the
OFF
cycle ON if duty cycle is > 0
MOSFET is off
high-side MOSFET is turned off
For proper operation, the total gate charge of the MOSFET connected to LDRV should be less than 50nC.
Copyright 2006–2007, Texas Instruments Incorporated
23
Product Folder Link(s) :TPS40075
相關PDF資料
PDF描述
TPS40075RHLTG4 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20
TPS40077PWPR 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40077PWPRG4 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40077PWPG4 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS40090QPWRQ1 SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PDSO24
相關代理商/技術參數
參數描述
TPS40075RHLRG4 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40075RHLT 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40075RHLTG4 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40077 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-EFFICIENCY, MIDRANGE-INPUT, SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
TPS40077_07 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-EFFICIENCY, MIDRANGE-INPUT, SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*