參數資料
型號： TPS40180RGER
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 0.05 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24
封裝： GREEN, PLASTIC, VQFN-24
文件頁數： 11/52頁
文件大?。?/td> 1291K
代理商： TPS40180RGER
www.ti.com
=
+
e
pk
L
COMP
V
(I
R ) 12.5
(8)
(
)
f
IN
OUT
RIPPLE
IN
SW
V
1
I
L
V
-
=
÷
÷
÷
÷
è
è
è
(9)
=
+
÷
è
RIPPLE
PK
OUT
I
2
(10)
=
+
OUT
RMP
VSH
IN
V
Ve
V
(11)
=
+
÷
è
OUT
RMP
VSH
PK
L
IN
V
COMP
V
(I
R ) 12.5
V
(12)
a =
÷
è
RMP
IN
V
(13)
(
)
÷
b =
+
÷
è
RMP
L
PK
ph
V
R
12.5 I
2 N
(14)
(
)
VSH
ILIM
V
R1
1
I
b + a
=
- a
(15)
SLVS753B – FEBRUARY 2007 – REVISED NOVEMBER 2007
Overcurrent protection for the TPS40180 is set by connecting a resistor from the ILIM pin to the VSH pin. A
current source of 23.5
A out of the ILIM pin sets a voltage level on the ILIM pin and the COMP pin is not
allowed to rise above this level. Since the device uses current mode control and COMP cannot rise above this
level, an effective maximum output current is defined. The second resistor on the ILIM pin, R2, is optional and if
used is connected to the output voltage. This resistor provides compensation of the overcurrent level for changes
in output voltage, such as would be seen at startup. If not used, the overcurrent threshold level is higher at
output voltages lower than the designed target.
The output current, flows through the inductor resistance and develops a voltage, VC across it, representative of
the output current. This resistance voltage is extracted from the total inductor voltage by the R-C network placed
across the inductor. This voltage is amplified with a gain of 12.5 and then subtracted from the error amplifier
output, COMP, to generate the Ve voltage. The Ve signal is compared to the slope-compensation RAMP signal
to generate the PWM signal that is used to control the FET drivers. As the output current is increased, the
amplified VC causes the Ve signal to decrease. In order to maintain the proper duty cycle, the COMP signal must
increase. Therefore, the magnitude of the COMP signal contains the output current information as shown in
In order to satisfy the input-output voltage relationship, the Equation 11 must hold:
Combining Equation 8 and Equation 11 and solving for the COMP voltage gives:
Since COMP and ILIM are of equal voltage when at the current limit condition, setting ILIM to the expected
COMP voltage at maximum current is how the current limit threshold is set. To calculate the resistors R1 and R2
from Figure 25, proceed as follows:
Copyright 2007, Texas Instruments Incorporated
19
Product Folder Link(s): TPS40180
相關PDF資料
PDF描述
TPS2321IDG4 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
TK11819MTL SWITCHING REGULATOR, PDSO6
TH74KA22BVWORPGD/T SPECIALTY ANALOG CIRCUIT, CQCC84
TH7422BVWONGS SPECIALTY ANALOG CIRCUIT, CQCC84
TC520ACOE713 SPECIALTY ANALOG CIRCUIT, PDSO16
相關代理商/技術參數
參數描述
TPS40180RGERG4 功能描述:DC/DC 開關控制器 Single Ph Stackable Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40180RGET 功能描述:DC/DC 開關控制器 Single Ph Stackable Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40180RGETG4 功能描述:DC/DC 開關控制器 Sgl Phase Stackable Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS40190 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW PIN COUNT SYNCHRONOUS BUCK CONTROLLER
TPS40190DRC 制造商:Texas Instruments 功能描述:DC/DC CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*