參數資料
型號: TPS54160DGQR
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 2.7 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10
封裝: GREEN, PLASTIC, MSOP-10
文件頁數: 33/50頁
文件大?。?/td> 1375K
代理商: TPS54160DGQR
BOOT
VIN
EN
SS/TR
RT/CLK
PH
GND
COMP
VSENSE
PWRGD
Input
Bypass
Capacitor
UVLO
Adjust
Resistors
SlowStart
Capacitor
Frequency
SetResistor
Compensation
Network
Resistor
Divider
Output
Inductor
Output
Capacitor
Vout
Vin
Topside
Ground
Area
Catch
Diode
RouteBootCapacitor
Traceonanotherlayerto
providewidepathfor
topsideground
ThermalVIA
SignalVIA
www.ti.com
SLVS795C – OCTOBER 2008 – REVISED OCTOBER 2010
Layout
Layout is a critical portion of good power supply design. There are several signals paths that conduct fast
changing currents or voltages that can interact with stray inductance or parasitic capacitance to generate noise
or degrade the power supplies performance. To help eliminate these problems, the VIN pin should be bypassed
to ground with a low ESR ceramic bypass capacitor with X5R or X7R dielectric. Care should be taken to
minimize the loop area formed by the bypass capacitor connections, the VIN pin, and the anode of the catch
diode. See Figure 65 for a PCB layout example. The GND pin should be tied directly to the power pad under the
device and the power pad.
The power pad should be connected to any internal PCB ground planes using multiple vias directly under the
device. The PH pin should be routed to the cathode of the catch diode and to the output inductor. Since the PH
connection is the switching node, the catch diode and output inductor should be located close to the PH pins,
and the area of the PCB conductor minimized to prevent excessive capacitive coupling. For operation at full rated
load, the top side ground area must provide adequate heat dissipating area. The RT/CLK pin is sensitive to noise
so the RT resistor should be located as close as possible to the device and routed with minimal lengths of trace.
The additional external components can be placed approximately as shown. It may be possible to obtain
acceptable performance with alternate PCB layouts, however this layout has been shown to produce good
results and is meant as a guideline.
Figure 65. PCB Layout Example
Copyright 2008–2010, Texas Instruments Incorporated
39
Product Folder Link(s): TPS54160
相關PDF資料
PDF描述
TPS5420MDREPG4 5.2 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8
TPS5420MDREP 5.2 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8
TPS54225PWP 4.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14
TPS54225PWPR 4.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14
TPS54225TPWPRQ1 SWITCHING REGULATOR, PDSO14
相關代理商/技術參數
參數描述
TPS54160DGQRG4 功能描述:直流/直流開關調節器 3.5-60V,1.5A Step Down SWIFT Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS54160DRCR 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.5-A, 60-V, STEP-DOWN SWIFT DC/DC CONVERTER WITH ECO-MODE
TPS54160DRCT 制造商:TI 制造商全稱:Texas Instruments 功能描述:1.5-A, 60-V, STEP-DOWN SWIFT DC/DC CONVERTER WITH ECO-MODE
TPS54160EVM-230 功能描述:電源管理IC開發工具 TPS54160 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS54160EVM-535 功能描述:電源管理IC開發工具 Eval Mod for High Brightness LED Drvr RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V