- 您現在的位置：買賣IC網 > PDF目錄68419 > TPS61141DRCR (TEXAS INSTRUMENTS INC) 1.26 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 PDF資料下載
參數資料
| 型號： | TPS61141DRCR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.26 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | 3 X 3 MM, GREEN, PLASTIC, QFN-10 |
| 文件頁數： | 6/25頁 |
| 文件大?。?/td> | 776K |
| 代理商： | TPS61141DRCR |
www.ti.com
APPLICATION INFORMATION
MAXIMUM OUTPUT CURRENT – PWM CONTROL
Ip +
1
L
1
Viout)Vf*Vin
)
1
Vin
Fs
(3)
Iout_max +
Vin
Ilim *
Ip
2
h
Viout
(4)
MAXIMUM OUTPUT CURRENT – PFM CONTROL
Ton +
L
I
lim
V
in
(5)
T
off +
L
I
lim
V
iout )
V * Vin
(6)
Iout_max +
h
I
lim
V
IN
2V
iout
Ton ) Toff
Ton ) Toff_min
(7)
SLVS624B – JANUARY 2006 – REVISED MARCH 2007
The over-current limit in a boost converter limits the maximum input current and thus maximum input power for a
given input voltage. Maximum output power is less than maximum input power due to power conversion losses.
Therefore, the current limit setting, input voltage, output voltage and efficiency can all change maximum current
output. Since current limit clamps peak inductor current, ripple has to be subtracted to derive maximum DC
current. The ripple current is a function of switching frequency, inductor value and duty cycle. The following
equations take into account of all the above factors for maximum output current calculation.
where
Ip = inductor peak to peak ripple
L = inductor value
Vf = power diode forward voltage
Fs = Switching frequency
Viout = boost output voltage. It is equal to the higher of either 330 mV + Vout or 330 mV + voltage drop
across WLED.
where
Iout_max = Maximum output current of the boost converter
Ilim = overcurrent limit
η = efficiency
To keep a tight range of the overcurrent limit, The TPS61140/1 uses the Vin and Iout pin voltage to compensate
for the overcurrent limit variation caused by the slope compensation. However, the current threshold still has
residual dependency on the Vin and Iout voltage. Use Figure 16 and Figure 17 to identify the typical overcurrent
limit in your application, and use
±25% tolerance to account for temperature dependency and process variations.
The maximum output current can also be limited by the current capability of the LDO and the current sink
circuitry. Both are designed to provide maximum 35 mA current regardless of the current capability of the boost
converter.
When only voltage output is selected, the boost operates in PFM mode, and the maximum output current can be
calculated as,
Toff_min = minimum off time
14
相關PDF資料 |
PDF描述 |
|---|---|
| TPS62002DGSG4 | 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62005DGSRG4 | 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62003DGSR | 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62003DGS | 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62008DGSG4 | 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS61141DRCRG4 | 功能描述:LED照明驅動器 Dual 700mA Switch 1.2MHz Boost Cnvrtr RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| TPS61141DRCT | 功能描述:LED照明驅動器 Dual 700mA Switch 1.2MHz Boost Cnvrtr RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| TPS61141DRCTG4 | 功能描述:LED照明驅動器 Dual 700mA Switch 1.2MHz Boost Cnvrtr RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| TPS61150 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL OUTPUT BOOST WLED DRIVER USING SINGLE INDUCTOR |
| TPS61150A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL OUTPUT BOOST WLED DRIVER USING SINGLE INDUCTOR |
發布緊急采購，3分鐘左右您將得到回復。