參數資料
型號: TPS61200DRCTG4
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 1.5 A BATTERY CHARGE CONTROLLER, 1650 kHz SWITCHING FREQ-MAX, PDSO10
封裝: 3 X 3 MM, GREEN, PLASTIC, SON-10
文件頁數: 8/28頁
文件大小: 1012K
代理商: TPS61200DRCTG4
www.ti.com
INMIN
UVLO
V
R3 = R4 x
- 1
V
÷
÷
è
(2)
Inductor Selection
MIN
IN
s
L
= V
x 0.5
A
m
(3)
(
)
IN
OUT
IN
OUT
LMAX
IN
OUT
V
x
V
x I
I
=
+
0.8 x V
2 x V
x f x L
-
(4)
Capacitor Selection
Input Capacitor
Output Capacitor
OUT
F
C
= 5 x L x
H
m
(5)
SLVS577B – MARCH 2007 – REVISED FEBRUARY 2008
To make sure that the TPS6120X devices can operate, an inductor must be connected between pin VIN and pin
L. To estimate the minimum inductance value Equation 3 can be used.
In Equation 3, the minimum inductance, LMIN, for boost mode operation is calculated. VIN is the maximum input
voltage. The recommended inductor value range is between 1.5
H and 4.7 H. The minimum inductor value
should not be below 1.5
H, even if Equation 3 yields in something lower. Using 2.2 H is recommended anyway
for getting best performance over the whole input and output voltage range.
With the chosen inductance value, the peak current for the inductor in steady state operation can be calculated.
Equation 4 shows how to calculate the peak current I.
This would be the critical value for the current rating for selecting the inductor. It also needs to be taken into
account that load transients and error conditions may cause higher inductor currents. The following inductor
series from different suppliers have been used with TPS6120x converters:
Table 1. List of Inductors
VENDOR
INDUCTOR SERIES
LPS3015
Coilcraft
LPS4012
Murata
LQH3NP
Tajo Yuden
NR3015
Wurth Elektronik
WE-TPC Typ S
At least a 4.7
F input capacitor is recommended to improve transient behavior of the regulator and EMI
behavior of the total power supply circuit. A ceramic capacitor placed as close as possible to the VIN and PGND
pins of the IC is recommended.
For the output capacitor, it is recommended to use small ceramic capacitors placed as close as possible to the
VOUT and PGND pins of the IC. If, for any reason, the application requires the use of large capacitors which can
not be placed close to the IC, using a smaller ceramic capacitor in parallel to the large one is recommended.
This small capacitor should be placed as close as possible to the VOUT and PGND pins of the IC.
To get an estimate of the recommended minimum output capacitance, Equation 5 can be used.
A capacitor with a value in the range of the calculated minimum should be used. This is required to maintain
control loop stability. There are no additional requirements regarding minimum ESR. There is also no upper limit
for the output capacitance value. Larger capacitors cause lower output voltage ripple as well as lower output
voltage drop during load transients.
16
Copyright 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS61200 TPS61201 TPS61202
相關PDF資料
PDF描述
TL4051CIDCKTG4 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.212 V, PDSO5
TK75003UIBX SWITCHING CONTROLLER, 100 kHz SWITCHING FREQ-MAX, PDSO5
TD300-024-24-CP 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE
TD300-048-12-IN 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE
TD300-150-24-CN 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
TPS61200EVM-179 功能描述:電源管理IC開發工具 TPS61200EVM-179 Evaluation Module RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS61201 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW INPUT VOLTAGE SYNCHRONOUS BOOST CONVERTER WITH 1.3-A SWITCHES
TPS61201DRC 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW INPUT VOLTAGE SYNCHRONOUS BOOST CONVERTER WITH 1.3-A SWITCHES
TPS61201DRCR 功能描述:直流/直流開關調節器 0.3V In Vltg Boost RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS61201DRCRG4 功能描述:直流/直流開關調節器 0.3V In 3.3V Out Vltg Boost Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5