參數資料
型號: TPS61221DCKR
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 0.4 A BATTERY CHARGE CONTROLLER, PDSO6
封裝: GREEN, PLASTIC, SC-70, 6 PIN
文件頁數: 5/22頁
文件大?。?/td> 1333K
代理商: TPS61221DCKR
APPLICATION INFORMATION
DESIGN PROCEDURE
Programming the Output Voltage
L
1
VIN
VOUT
FB
C
2
EN
GND
TPS6122x
fixedoutputvoltage
VOUT
VIN
C
1
÷
è
OUT
FB
V
R
= R
x
- 1
1
2
V
(1)
L
1
VIN
VOUT
FB
C
2
EN
GND
TPS6122x
VOUT
R
1
R
2
V
IN
C
1
www.ti.com ............................................................................................................................................................................................... SLVS776 – JANUARY 2009
The TPS6122x DC/DC converters are intended for systems powered by a single cell battery to up to three
Alkaline, NiCd or NiMH cells with a typical terminal voltage between 0.7 V and 5.5 V. They can also be used in
systems powered by one-cell Li-Ion or Li-Polymer batteries with a typical voltage between 2.5 V and 4.2 V.
Additionally, any other voltage source with a typical output voltage between 0.7 V and 5.5 V can be used with the
TPS6122x family.
Fixed output voltage versions
At fixed voltage versions, the output voltage is set by a resistor divider internally. The FB pin is used to sense the
output voltage. To configure the fixed output devices properly, the FB pin needs to be connected directly to
VOUT as shown in Figure 24.
Figure 24. Typical Application Circuit for Fixed Output Voltage Option
Adjustable output voltage version
In the adjustable output versions, an external resistor divider is used to adjust the output voltage. The resistor
divider needs to be connected between VOUT, FB and GND as shown in Figure 25. When the output voltage is
regulated properly, the typical voltage value at the FB pin is 500 mV for the adjustable devices. The maximum
recommended value for the output voltage is 5.5 V. The current through the resistive divider should be about 100
times greater than the current into the FB pin. The typical current into the FB pin is 0.01
A, and the voltage
across the resistor between FB and GND, R2, is typically 500 mV. Based on those two values, the recommended
value for R2 should be lower than 500 k, in order to set the divider current to 1 A or higher. The value of the
resistor connected between VOUT and FB, R1, depending on the needed output voltage (VOUT), can be
calculated using Equation 1:
As an example, if an output voltage of 3.3 V is needed, a 1-M
resistor is calculated for R1 when for R2 a 180-k
has been selected.
Figure 25. Typical Application Circuit for Adjustable Output Voltage Option
Copyright 2009, Texas Instruments Incorporated
13
Product Folder Link(s): TPS61220 TPS61221 TPS61222
相關PDF資料
PDF描述
TPS61251DSGT SWITCHING REGULATOR, 3500 kHz SWITCHING FREQ-MAX, PDSO8
TPS61251DSG SWITCHING REGULATOR, 3500 kHz SWITCHING FREQ-MAX, PDSO8
TPS62000YEGR 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, BGA12
TPS62000YEGT 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, BGA12
TPS62000YEG 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, BGA12
相關代理商/技術參數
參數描述
TPS61221DCKT 功能描述:直流/直流開關調節器 Tiny Low Inp Vltg Boost Cnvrtr RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS61222DCKR 功能描述:直流/直流開關調節器 Tiny Low Inp Vltg Boost Cnvrtr RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS61222DCKT 功能描述:直流/直流開關調節器 Tiny Low Inp Vltg Boost Cnvrtr RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS61222MDCKTEP 功能描述:直流/直流開關轉換器 Boost Converter with 5.5?A Quiescnt Crrnt RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
TPS61223DCKR 制造商:Texas Instruments 功能描述: