參數資料
型號: TPS62003DGSR
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10
封裝: GREEN, PLASTIC, MSOP-10
文件頁數: 7/26頁
文件大小: 869K
代理商: TPS62003DGSR
INPUT CAPACITOR SELECTION
O
RMS
O(max)
I
V
I
= I
1
V
-
÷
è
(7)
The worst case RMS ripple current occurs at D = 0.5 and is calculated as:
O
RMS
I
=
2
LAYOUT CONSIDERATIONS
VIN
1
8
6
7
3
2
9
5
10
4
L1
EN
ILIM
SYNC
GND
FC
PG
PGND
FB
L
TPS62000
+
Co
VO
C3
Ci
VI
R3
R1
C(ff)
R2
+
PG
www.ti.com ........................................................................................................................................... SLVS294E – SEPTEMBER 2000 – REVISED AUGUST 2008
Table 3. Tested Capacitors
CAPACITOR VALUE
ESR/m
COMPONENT SUPPLIER
COMMENTS
10
F
50
Taiyo Yuden JMK316BJ106KL
Ceramic
47
F
100
Sanyo 6TPA47M
POSCAP
68
F
100
Spraque 594D686X0010C2T
Tantalum
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high input
voltage spikes.
The input capacitor should have a minimum value of 10
F and can be increased without any limit for better input
voltage filtering.
The input capacitor should be rated for the maximum input ripple current calculated as:
Ceramic capacitor show a good performance because of their low ESR value, and they are less sensitive against
voltage transients compared to tantalum capacitors.
Place the input capacitor as close as possible to the input pin of the IC for best performance.
As for all switching power supplies, the layout is an important step in the design especially at high peak currents
and switching frequencies. If the layout is not carefully done, the regulator might show stability problems as well
as EMI problems.
Therefore, use wide and short traces for the main current paths as indicted in bold in Figure 16. The input
capacitor should be placed as close as possible to the IC pins as well as the inductor and output capacitor. Place
the bypass capacitor, C3, as close as possible to the FC pin. The analog ground, GND, and the power ground,
PGND, need to be separated. Use a common ground node as shown in Figure 16 to minimize the effects of
ground noise.
Figure 16. Layout Diagram
Copyright 2000–2008, Texas Instruments Incorporated
15
相關PDF資料
PDF描述
TPS62003DGS 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10
TPS62008DGSG4 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10
TPS62000DGS 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10
TPS62007DGSRG4 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10
TPS62004DGSR 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10
相關代理商/技術參數
參數描述
TPS62003DGSRG4 功能描述:直流/直流開關調節器 1.2V Out 600mA Step-Down Con RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS62004DGS 功能描述:直流/直流開關調節器 1.5V Out 600mA Step-Down Con RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS62004DGSG4 功能描述:直流/直流開關調節器 1.5V Out 600mA Step-Down Con RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS62004DGSR 功能描述:直流/直流開關調節器 1.5V Out 600mA Step-Down Con RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS62004DGSRG4 功能描述:直流/直流開關調節器 1.5V Out 600mA Step-Down Con RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5