參數資料
型號： TPS62361BYZHT
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 4.3 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, BGA16
封裝： 2 X 2 MM, GREEN, DSBGA-16
文件頁數： 15/52頁
文件大?。?/td> 1125K
代理商： TPS62361BYZHT
SLVSAU9A
– MAY 2011 – REVISED AUGUST 2011
The I2C interface is operable when VDD and AVIN are present, regardless of the state of the EN pin.
If the device is disabled by pulling the EN to a logic low, the output capacitor can actively be discharged. Per
default, this feature is disabled. Programming the EN_DISC bit to a logic high will discharge the output capacitor
via a typ. 300
Ω path on the SENSE+ pin.
SOFT START
The device incorporates an internal soft start circuitry that controls the ramp up of the output voltage after
enabling the device. This circuitry eliminates inrush current to avoid excessive voltage drops of primary cells and
rechargeable batteries with high internal impedance.
During soft start, the output voltage is monotonically ramped up to the minimum programmable output voltage.
After reaching this threshold, the output voltage is further increased following the slope as programmed in the
ramp rate settings (see RAMP RATE CONTROLLING) until reaching the programmed output voltage. Once the
nominal voltage is reached, regular operation as described above will continue.
The device is able to start into a pre biased output capacitor as well.
PROGRAMMING THE OUTPUT
The TPS6236x devices offer four similar registers to program the output. Two dedicated hardware input pins,
VSEL0 and VSEL1, are implemented for choosing the active register. The logic state of VSEL0 and VSEL1
select the register whose settings are present at the output. The VSEL0 and VSEL1 pins must be terminated
unless the internal pull-down resistors are activated.
The registers have a certain initial default value (see Table 2) and can be readjusted via I2C during operation.
This allows a simple transition between several output options by triggering the dedicated input pins. At the same
time since the presets can be readjusted during operation, this offers highest flexibility.
Table 2. Output Presets
DEFAULT OPERATION
INPUT PINS
DEFAULT OUTPUT VOLTAGE [V]
MODE
PRESET
I2C REGISTER
TPS62360, TPS62361B,
VSEL1
VSEL0
TPS62360
TPS62361B
TPS62362
0
SET0
0x00h
– see Table 12,
Power Save Mode
1.40
0.96
1.23
0
1
SET1
0x01h
– see Table 15,
Power Save Mode
1.00
1.40
1.00
1
0
SET2
0x02h
– see Table 18,
Power Save Mode
1.40
1.16
1.20
1
SET3
0x03h
– see Table 21,
Power Save Mode
1.10
1.16
1.10
Via the I2C interface and/or the four preset options, the following output parameters can be changed:
Output voltage from 0.77 V to 1.4 V (TPS62360/62) and 0.5V to 1.77V (TPS62361B) with 10 mV granularity
Mode of operation: Power Save Mode or forced PWM mode
The slope for transition between different output voltages (Ramp Rate) can be changed via I2C as well. The
slope applies for all presets globally. See RAMP RATE CONTROLLING for further details.
Since the output parameters can be changed by dedicated pins for selecting presets and by I2C, the following
use scenarios are feasible:
Control the device via dedicated pins only, after programming the presets, to choose and change within the
programmed settings
Program via I2C only. The dedicated input pins have fixed connections. Changes are conducted by changing
the preset values of the active register.
Dedicated input pins and I2C mixed operation. The non active presets might be changed. The dedicated input
pins are used for the transition to the new output condition. Changes within an active preset via I2C are
feasible as well.
22
Copyright
2011, Texas Instruments Incorporated
Product Folder Link(s): TPS62360 TPS62361B TPS62362
相關PDF資料
PDF描述
TPS62400QDRCQ1 SWITCHING REGULATOR, PDSO10
TPS62410DRCTG4 1.6 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO10
TPS62420DRCT 1.61 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO10
TPS62420DRC 1.61 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO10
TPS62421DRCR 1.61 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO10
相關代理商/技術參數
參數描述
TPS62362EVM-655 功能描述:電源管理IC開發工具 TPS62362 EVAL MOD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS62362YZHR 功能描述:直流/直流開關轉換器 PROC CORE SUPPLY RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
TPS62362YZHT 功能描述:直流/直流開關轉換器 PROC CORE SUPPLY RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
TPS62363YZHR 功能描述:直流/直流開關轉換器 Proc Core Supply w/ I2C Comp Interface RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
TPS62363YZHT 功能描述:直流/直流開關轉換器 Proc Core Supply w/ I2C Comp Interface RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*