- 您現在的位置：買賣IC網 > PDF目錄98287 > TS(X)8387CF 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 PDF資料下載
參數資料
| 型號： | TS(X)8387CF |
| 元件分類： | ADC |
| 英文描述： | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| 封裝： | CERAMIC, QFP-68 |
| 文件頁數： | 18/38頁 |
| 文件大?。?/td> | 617K |
| 代理商： | TS(X)8387CF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
TS8387
25/38
7. APPLYING THE TS8387
Advanced Application Notes
7.1.
TIMING INFORMATIONS
7.1.1.Timing Values for TS8387F (refer to timing diagram and switching characteristics p8 and p9) :
The min/max timing values are valid over the full temperature range in the following conditions :
Note 1 : Specified Termination Load (Differential output Datas and Data Ready) :
50 ohms resistor in parallel with 1 standard ECLinPS register from Motorola, (e.g : 10E452)
(Typical ECLinPS inputs shows a typical input capacitance of 1.5 pF (including package and ESD protections)
If addressing an output Dmux, take care if some Digital outputs do not have the same termination load and apply corre-
sponding derating value given below.
Note 2 : Output Termination Load derating values for TOD and TDR :
35 ps/pF or 50 ps per additionnal ECLinPS load.
Note 3 :Propagation time delay derating values have also to be applied for TOD and TDR :
6 ps/mm (155 ps/inch) for TSEV8387F Evaluation Board.
Apply proper time delay derating value if a different dielectric layer is used.
7.1.2.Propagation time considerations :
TOD and TDR Timing values are given from Pin to Pin and DO NOT include the additionnal propagation times between
die Pads and input/output termination loads. For the TSEV8387F Evaluation Board, the propagation time delay is 6ps/
mm (155ps/inch) corresponding to 3.4 (@10GHz) dielectric constant of the RO4003 used for the Board.
If a different dielectric layer is used (for instance Teflon), please use appropriate propagation time values.
TD does NOT depend on propagation times because it is a differential data.
(TD is the time difference between Data Ready output delay and digital Data output delay)
TD is also the most straightforward data to measure, again because it is differential :
TD can be measured directly onto termination loads, with matched Oscilloscopes probes.
7.1.3.TOD –TDR variation over temperature :
Values for TOD and TDR track each other over temperature ( 1 percent variation for TOD – TDR per 100 degrees Cel-
sius temperature variation ). Therefore TOD – TDR variation over temperature is negligible. Moreover, the internal
(onchip) and package skews between each Data TODs and TDR effect can be considered as negligible.
Consequently, minimum values for TOD and TDR are never more than 100 ps apart. The same is true for the TOD and
TDR maximum values. In other terms :
If TOD is at 900 ps, TDR will not be at 1300 ps ( maximum time delay for TDR ).
If TOD is at 1400 ps, TDR will not be at 800 ps ( minimum time delay for TDR ) However, external TOD – TDR values may
be dictated by total digital datas skews between every TODs (each digital data) and TDR :
MCM Board, bonding wires and output lines lengths differences, and output termination impedance mismatches.
The external (on board) skew effect has NOT been taken into account for the specification of the minimum and maxi-
mum values for TOD–TDR.
7.1.4.Principle of operation :
Refer to the Specification Timing Diagrams ( Fig.1 p9).
The analog input waveform is sampled and held on the rising edge of the clock input, and the digital data is available
after 2.5 clock periods latency, on the clock falling edge, after a 1000 ps output delay time (TOD). ( To be confirmed at
given temperatures).
The 2.5 period latency is explained by the fact the TS8387 uses both clock edges in its internal timing circuitry, and the
multiple banks of regeneration latches which are used allows for 10 E–18 value for the Bit Error Rate at 500Msps.
TOD is measured from the falling edge zero crossing point of the differential clock input, to the zero crossing point of a
change of the differential data output.
TDR is measured from the rising edge zero crossing point of the differential clock input, to the rising edge zero crossing
point of a change of the DATA READY signal.
High Speed Digital Output Data Storing :
The TS8387 features one single output data port.
The TS8387 data output delay time and Data Ready signal timings have been set up in order to be compatible with fast
ECL data storing registers like for instance the ECLinPS Logic devices from MOTOROLA.
相關PDF資料 |
PDF描述 |
|---|---|
| TS8387MF | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8387CF | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS(X)8387CF | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8387CF_ | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS(X)8387CF_ | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSX-8A16MHZ | 制造商:Epson Electronics America Inc 功能描述:CODE BCAI |
| TSX920ILT | 功能描述:General Purpose Amplifier 1 Circuit Rail-to-Rail SOT-23-6 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 放大器類型:通用 電路數:1 輸出類型:滿擺幅 壓擺率:17 V/μs 增益帶寬積:10MHz -3db 帶寬:- 電流 - 輸入偏置:10pA 電壓 - 輸入失調:4mV 電流 - 電源:2.9mA 電流 - 輸出/通道:74mA 電壓 - 電源，單/雙（±）:4 V ~ 16 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1 |
| TSX921ILT | 制造商:STMicroelectronics 功能描述:ANALOG AND AUDIO SYSTEMS - Tape and Reel 制造商:STMicroelectronics 功能描述:ANALOG and AUDIO SYSTEMS |
| TSX921IYLT | 制造商:STMicroelectronics 功能描述:IC OPAMP R-R 10MHZ SOT23-5 |
| TSX922IDT | 功能描述:General Purpose Amplifier 2 Circuit Rail-to-Rail 8-SO 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 放大器類型:通用 電路數:2 輸出類型:滿擺幅 壓擺率:17 V/μs 增益帶寬積:10MHz -3db 帶寬:- 電流 - 輸入偏置:10pA 電壓 - 輸入失調:4mV 電流 - 電源:2.8mA 電流 - 輸出/通道:74mA 電壓 - 電源，單/雙（±）:4 V ~ 16 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SO 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。