參數資料
型號： TS4956EIJT
廠商： STMICROELECTRONICS
元件分類： 音頻／視頻放大
英文描述： 1.055 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA18
封裝： ROHS COMPLIANT, FCP-18
文件頁數： 32/55頁
文件大?。?/td> 1711K
代理商： TS4956EIJT
TS4956
Application information
38/55
4
Application information
The TS4956 integrates four monolithic power amplifiers and has one differential input and
two single-ended inputs. The output amplifiers can be configured in 7 different modes as
one SE (single-ended) capacitively-coupled output, two phantom ground headphone
outputs and two BTL outputs. Figure 1 on page 5 and Figure 2 on page 6 show these
configuration schemes and Table 7 on page 8 describes these configurations in different
modes.
This chapter gives information on how to configure the TS4956 in an application.
4.1
Output configurations
4.1.1
Shutdown
When the device is in shutdown mode, all of the device’s outputs are in a high impedance
state.
4.1.2
Single-ended output configuration (modes 5 and 6)
When the device is woken-up via the IC interface, output amplifier on output MLO is biased
to the VCC/2 voltage. In this configuration an output capacitor, Cout, on the single-ended
output is needed to block the VCC/2 voltage and couples the audio signal to the load.
VCC/2 voltage is present on this output in all modes (modes 1 to 7) to keep the output
capacitor Cout charged and to improve pop performance on this output during the switching
between any given mode to mode 5 or 6.
When the device is in mode 5 or 6 where the single-ended output MLO is active, all other
outputs are in a high impedance state.
4.1.3
Phantom ground output configuration (modes 3 and 4)
In a phantom ground output configuration (modes 3 and 4) the internal buffer is connected
to the PHG pin and biased to the VCC/2 voltage. Output amplifiers (pins LHP and RHP) are
also biased to the VCC/2 voltage. One end of the load is connected to output amplifier and
one to the PHG buffer. Therefore, no output capacitors are needed. The advantage of the
PHG output configuration is that there are fewer external components compared to an SE
configuration. However, note that in this configuration, the device has a higher power
All other inactive outputs are in the high impedance state except for the MLO output, which
is biased to VCC/2 voltage.
To achieve better crosstalk results in this case, each speaker should be connected with a
separate PHG wire (two speakers connected with four wires) as shown in Figure 1 on
page 5 (instead of using only one common PHG wire for both speakers, that is, two
speakers connected with three wires).
相關PDF資料
PDF描述
TS4956EIKJT 1.055 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA18
TS4956EKIJT 1.06 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA18
TS4961TIQT 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC16
TS4962EIJT 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
TS4962EIKJT 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
相關代理商/技術參數
參數描述
TS4956EIKJT 功能描述:音頻放大器 Stereo Audio Amp System RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TS4961TIQT 功能描述:音頻放大器 MONO CLASS D AUDIO PWR AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TS4962 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8W filter-free mono class D audio power amplifier
TS4962_07 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8W filter-free mono class D audio power amplifier
TS4962_10 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8 W filter-free mono class D audio power amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*