- 您現在的位置：買賣IC網 > PDF目錄98290 > TS4961TIQT (STMICROELECTRONICS) 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC16 PDF資料下載
參數資料
| 型號： | TS4961TIQT |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.5 W, 1 CHANNEL, AUDIO AMPLIFIER, QCC16 |
| 封裝： | 3 X 3 MM, ROHS COMPLIANT, QFN-16 |
| 文件頁數： | 35/49頁 |
| 文件大小： | 1351K |
| 代理商： | TS4961TIQT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Application component information
TS4961T
40/49
4.8
Output filter considerations
The TS4961T is designed to operate without an output filter. However, due to very sharp
transients on the TS4961T output, EMI radiated emissions may cause some standard
compliance issues.
These EMI standard compliance issues can appear if the distance between the TS4961T
outputs and loudspeaker terminal are long (typically more than 50 mm, or 100 mm in both
directions, to the speaker terminals). Since the PCB layout and internal equipment device
are different for each configuration, it is difficult to provide a one-size-fits-all solution.
However, to decrease the probability of EMI issues, there are several simple rules to follow.
●
Reduce, as much as possible, the distance between the TS4961T output pins and the
speaker terminals.
●
Use ground planes for shielding sensitive wires.
●
Place, as close as possible to the TS4961T and in series with each output, a ferrite
bead with a rated current of 2.5 A minimum, and impedance greater than 50
Ω at
frequencies above 30 MHz. If, after testing, these ferrite beads are not necessary,
replace them by a short circuit.
●
Allow enough footprint to place, if necessary, a capacitor to short perturbations to
ground as shown in Figure 78.
Figure 78.
Output filter for shorting pertubations to ground
In the case where the distance between the TS4961T outputs and speaker terminals is high,
it is possible to have low frequency EMI issues due to the fact that the typical operating
frequency is 250 kHz.
In this configuration, it is recommended to use an output filter. It should be placed as close
as possible to the TS4961T.
Ferrite chip bead
about 100pF
Gnd
From TS4961T output
To speaker
相關PDF資料 |
PDF描述 |
|---|---|
| TS4962EIJT | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| TS4962EIKJT | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| TS4962EKIJT | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| TS4962IJT | 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| TS4962IQT | 2.8 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS4962 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8W filter-free mono class D audio power amplifier |
| TS4962_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8W filter-free mono class D audio power amplifier |
| TS4962_10 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2.8 W filter-free mono class D audio power amplifier |
| TS4962EIJT | 制造商:STMicroelectronics 功能描述:AUD AMP SPKR 1CH MONO 2W CLS-D 9PIN FLIP-CHIP - Tape and Reel |
| TS4962EKIJT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3W Filter-free Class D Audio Power Amplifier |
發布緊急采購，3分鐘左右您將得到回復。