參數資料
型號: TSL1401R-LF
廠商: TAOS Inc.
英文描述: 128 】 1 LINEAR SENSOR ARRAY WITH HOLD
中文描述: 128】1傳感器陣列線性拒不退讓
文件頁數: 9/12頁
文件大?。?/td> 207K
代理商: TSL1401R-LF
TSL1401RLF
128
×
1 LINEAR SENSOR ARRAY WITH HOLD
TAOS076B
APRIL 2007
9
The
LUMENOLOGY
Company
Copyright 2007, TAOS Inc.
www.taosinc.com
APPLICATION INFORMATION
The minimum integration time can be calculated from the equation:
T
int(min)
1
maximum clock frequency
(
n
18)
pixels
20
s
where:
n
is
the number of pixels
In the case of the TSL1401R
LF with the maximum clock frequency of 8 MHz, the minimum integration time
would be:
T
int(min)
0.125
s
(128
18)
20
s
33.75
s
It is good practice on initial power up to run the clock (
n
+1) times after the first SI pulse to clock out indeterminate
data from power up. After that, the SI pulse is valid from the time following (
n
+1) clocks. The output will go into
a high-impedance state after the
n
+1 high clock edge. It is good practice to leave the clock in a low state when
inactive because the SI pulse required to start a new cycle is a low-to-high transition.
The integration time chosen is valid as long as it falls in the range between the minimum and maximum limits
for integration time. If the amount of light incident on the array during a given integration period produces a
saturated output (Max Voltage output), then the data is not accurate. If this occurs, the integration period should
be reduced until the analog output voltage for each pixel falls below the saturation level. The goal of reducing
the period of time the light sampling window is active is to lower the output voltage level to prevent saturation.
However, the integration time must still be greater than or equal to the minimum integration period.
If the light intensity produces an output below desired signal levels, the output voltage level can be increased
by increasing the integration period provided that the maximum integration time is not exceeded. The maximum
integration time is limited by the length of time the integrating capacitors on the pixels can hold their accumulated
charge. The maximum integration time should not exceed 100 ms for accurate measurements.
It should be noted that the data from the light sampled during one integration period is made available on the
analog output during the next integration period and is clocked out sequentially at a rate of one pixel per clock
period. In other words, at any given time, two groups of data are being handled by the linear array: the previous
measured light data is clocked out as the next light sample is being integrated.
Although the linear array is capable of running over a wide range of operating frequencies up to a maximum
of 8 MHz, the speed of the A/D converter used in the application is likely to be the limiter for the maximum clock
frequency. The voltage output is available for the whole period of the clock, so the setup and hold times required
for the analog-to-digital conversion must be less than the clock period.
相關PDF資料
PDF描述
TSL1410R 1280 X 1 LINEAR SENSOR ARRAY WITH HOLD
TSL1412S 1536 】 1 LINEAR SENSOR ARRAY WITH HOLD
TSL2014 896 x 1 LINEAR SENSOR ARRAY
TSL201R-LF 64 x 1 LINEAR SENSOR ARRAY
TSL218 512 x 1 Pixel Linear Array
相關代理商/技術參數
參數描述
TSL1401USBEVM 功能描述:光學傳感器開發工具 TSL1401 Eval Module with USB Interface RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度:
TSL1402R 功能描述:光學開關,專業型 Linear Sensor 400 DPI RoHS:否 制造商:ams 感應方式: 安裝風格:Through Hole 封裝:Tube
TSL1406 制造商:未知廠家 制造商全稱:未知廠家 功能描述:768 X 1 LINEAR SENSOR ARRAY WITH HOLD
TSL1406R 功能描述:光學開關,專業型 400 DPI SENSOR (2) 384 PIXEL SECT. RoHS:否 制造商:ams 感應方式: 安裝風格:Through Hole 封裝:Tube
TSL1406RS 功能描述:光學開關,專業型 400 DPI SENSOR RoHS:否 制造商:ams 感應方式: 安裝風格:Through Hole 封裝:Tube