- 您現在的位置：買賣IC網 > PDF目錄373738 > TSL2561CS (TAOS Inc.) LIGHT-TO-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | TSL2561CS |
| 廠商： | TAOS Inc. |
| 英文描述： | LIGHT-TO-DIGITAL CONVERTER |
| 中文描述： | 光到數字轉換器 |
| 文件頁數： | 13/38頁 |
| 文件大?。?/td> | 441K |
| 代理商： | TSL2561CS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
TSL2560, TSL2561
LIGHT-TO-DIGITAL CONVERTER
TAOS059K
APRIL 2007
13
The
LUMENOLOGY
Company
Copyright 2007, TAOS Inc.
www.taosinc.com
Command Register
The command register specifies the address of the target register for subsequent read and write operations.
The Send Byte protocol is used to configure the COMMAND register. The command register contains eight bits
as described in Table 3. The command register defaults to 00h at power on.
Table 3. Command Register
6
7
5
4
ADDRESS
2
3
1
0
0
0
0
0
0
0
0
0
Reset Value:
COMMAND
CLEAR
CMD
WORD
BLOCK
FIELD
CMD
CLEAR
BIT
7
6
DESCRIPTION
Select command register. Must write as 1.
Interrupt clear. Clears any pending interrupt. This bit is a write-one-to-clear bit. It is self clearing.
SMB Write/Read Word Protocol. 1 indicates that this SMB transaction is using either the SMB Write Word or
Read Word protocol.
WORD
5
BLOCK
4
Block Write/Read Protocol. 1 indicates that this transaction is using either the Block Write or the Block Read
protocol. See Note below.
ADDRESS
3:0
Register Address. This field selects the specific control or status register for following write and read
commands according to Table 2.
NOTE: An I
2
C block transaction will continue until the Master sends a stop condition. See Figure 14 and Figure 15. Unlike the I2C protocol, the
SMBus read/write protocol requires a Byte Count. All four ADC Channel Data Registers (Ch through Fh) can be read simultaneously in
a single SMBus transaction. This is the only 32-bit data block supported by the TSL2560 SMBus protocol. The BLOCK bit must be set
to 1, and a read condition should be initiated with a COMMAND CODE of 9Bh. By using a COMMAND CODE of 9Bh during an SMBus
Block Read Protocol, the TSL2560 device will automatically insert the appropriate Byte Count (Byte Count = 4) as illustrated in Figure 15.
A write condition should not be used in conjunction with the Bh register.
Control Register (0h)
The CONTROL register contains two bits and is primarily used to power the TSL256x device up and down as
shown in Table 4.
Table 4. Control Register
6
7
5
4
POWER
2
3
1
0
0
0
0
0
0
0
0
0
Reset Value:
CONTROL
Resv
Resv
Resv
Resv
Resv
Resv
0h
FIELD
Resv
BIT
7:2
DESCRIPTION
Reserved. Write as 0.
Power up/power down. By writing a 03h to this register, the device is powered up. By writing a 00h to this
register, the device is powered down.
POWER
1:0
NOTE:
If a value of 03h is written, the value returned during a read cycle will be 03h. This feature can be
used to verify that the device is communicating properly.
相關PDF資料 |
PDF描述 |
|---|---|
| TSL2561T | LIGHT-TO-DIGITAL CONVERTER |
| TSL2562 | LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER |
| TSL2562CS | LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER |
| TSL2562T | LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER |
| TSL2563 | LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSL2561FN | 功能描述:光學數位轉換器 Light to Digital Sensor RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel |
| TSL2561T | 功能描述:光學數位轉換器 Light to Digital with I2C RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel |
| TSL2562 | 制造商:TAOS 制造商全稱:TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS 功能描述:LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER |
| TSL2562CL | 功能描述:光學數位轉換器 Ambient Light Sensor SMBus RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel |
| TSL2562CS | 功能描述:接口 - 專用 Ambient Light Sensor Light to Digital RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發(fā)布緊急采購，3分鐘左右您將得到回復。