參數資料
型號: TSL2561T
廠商: TAOS Inc.
英文描述: LIGHT-TO-DIGITAL CONVERTER
中文描述: 光到數字轉換器
文件頁數: 9/38頁
文件大?。?/td> 441K
代理商: TSL2561T
TSL2560, TSL2561
LIGHT-TO-DIGITAL CONVERTER
TAOS059K
APRIL 2007
9
The
LUMENOLOGY
Company
Copyright 2007, TAOS Inc.
www.taosinc.com
PRINCIPLES OF OPERATION
Analog-to-Digital Converter
The TSL256x contains two integrating analog-to-digital converters (ADC) that integrate the currents from the
channel 0 and channel 1 photodiodes. Integration of both channels occurs simultaneously, and upon completion
of the conversion cycle the conversion result is transferred to the channel 0 and channel 1 data registers,
respectively. The transfers are double buffered to ensure that invalid data is not read during the transfer. After
the transfer, the device automatically begins the next integration cycle.
Digital Interface
Interface and control of the TSL256x is accomplished through a two-wire serial interface to a set of registers
that provide access to device control functions and output data. The serial interface is compatible with System
Management Bus (SMBus) versions 1.1 and 2.0, and I
2
C bus Fast-Mode. The TSL256x offers three slave
addresses that are selectable via an external pin (ADDR SEL). The slave address options are shown in Table 1.
Table 1. Slave Address Selection
ADDR SEL TERMINAL LEVEL
GND
Float
VDD
SLAVE ADDRESS
0101001
0111001
1001001
SMB ALERT ADDRESS
0001100
0001100
0001100
NOTE: The Slave and SMB Alert Addresses are 7 bits. Please note the SMBus and I
2
C protocols on pages 9 through 12. A read/write bit should
be appended to the slave address by the master device to properly communicate with the TSL256X device.
SMBus and I
2
C Protocols
Each
Send
and
Write
protocol is, essentially, a series of bytes. A byte sent to the TSL256x with the most
significant bit (MSB) equal to 1 will be interpreted as a COMMAND byte. The lower four bits of the COMMAND
byte form the register select address (see Table 2), which is used to select the destination for the subsequent
byte(s) received. The TSL256x responds to any Receive Byte requests with the contents of the register
specified by the stored register select address.
The TSL256X implements the following protocols of the SMB 2.0 specification:
Send Byte Protocol
Receive Byte Protocol
Write Byte Protocol
Write Word Protocol
Read Word Protocol
Block Write Protocol
Block Read Protocol
The TSL256X implements the following protocols of the Philips Semiconductor I
2
C specification:
I
2
C Write Protocol
I
2
C Read (Combined Format) Protocol
相關PDF資料
PDF描述
TSL2562 LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
TSL2562CS LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
TSL2562T LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
TSL2563 LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
TSL2563CS LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
相關代理商/技術參數
參數描述
TSL2562 制造商:TAOS 制造商全稱:TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS 功能描述:LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
TSL2562CL 功能描述:光學數位轉換器 Ambient Light Sensor SMBus RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel
TSL2562CS 功能描述:接口 - 專用 Ambient Light Sensor Light to Digital RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
TSL2562FN 功能描述:光學數位轉換器 Ambient Light Sensor SMBus RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel
TSL2562T 功能描述:光學數位轉換器 Ambient light sensor SMBus & I2C interf. RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel