參數資料
型號: TSL2563
廠商: TAOS Inc.
英文描述: LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
中文描述: 低壓光到數字轉換器
文件頁數: 13/38頁
文件大小: 443K
代理商: TSL2563
TSL2562, TSL2563
LOW-VOLTAGE
LIGHT-TO-DIGITAL CONVERTER
TAOS066J
MAY 2007
13
The
LUMENOLOGY
Company
Copyright 2007, TAOS Inc.
www.taosinc.com
Command Register
The command register specifies the address of the target register for subsequent read and write operations.
The Send Byte protocol is used to configure the COMMAND register. The command register contains eight bits
as described in Table 3. The command register defaults to 00h at power on.
Table 3. Command Register
6
7
5
4
ADDRESS
2
3
1
0
0
0
0
0
0
0
0
0
Reset Value:
COMMAND
CLEAR
CMD
WORD
BLOCK
FIELD
CMD
CLEAR
BIT
7
6
DESCRIPTION
Select command register. Must write as 1.
Interrupt clear. Clears any pending interrupt. This bit is a write-one-to-clear bit. It is self clearing.
SMB Write/Read Word Protocol. 1 indicates that this SMB transaction is using either the SMB Write Word or
Read Word protocol.
WORD
5
BLOCK
4
Block Write/Read Protocol. 1 indicates that this transaction is using either the Block Write or the Block Read
protocol. See Note below.
ADDRESS
3:0
Register Address. This field selects the specific control or status register for following write and read
commands according to Table 2.
NOTE: An I
2
C block transaction will continue until the Master sends a stop condition. See Figure 14 and Figure 15. Unlike the I2C protocol, the
SMBus read/write protocol requires a Byte Count. All four ADC Channel Data Registers (Ch through Fh) can be read simultaneously in
a single SMBus transaction. This is the only 32-bit data block supported by the TSL2562 SMBus protocol. The BLOCK bit must be set
to 1, and a read condition should be initiated with a COMMAND CODE of 9Bh. By using a COMMAND CODE of 9Bh during an SMBus
Block Read Protocol, the TSL2562 device will automatically insert the appropriate Byte Count (Byte Count = 4) as illustrated in Figure 15.
A write condition should not be used in conjunction with the Bh register.
Control Register (0h)
The CONTROL register contains two bits and is primarily used to power the TSL256x device up and down as
shown in Table 4.
Table 4. Control Register
6
7
5
4
POWER
2
3
1
0
0
0
0
0
0
0
0
0
Reset Value:
CONTROL
Resv
Resv
Resv
Resv
Resv
Resv
0h
FIELD
Resv
BIT
7:2
DESCRIPTION
Reserved. Write as 0.
Power up/power down. By writing a 03h to this register, the device is powered up. By writing a 00h to this
register, the device is powered down.
POWER
1:0
NOTE:
If a value of 03h is written, the value returned during a read cycle will be 03h. This feature can be
used to verify that the device is communicating properly.
相關PDF資料
PDF描述
TSL2563CS LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
TSL2563T LOW-VOLTAGE LIGHT-TO-DIGITAL CONVERTER
TSL257-LF HIGH-SENSITIVITY LIGHT-TO-VOLTAGE CONVERTER
TSL257SM-LF HIGH-SENSITIVITY LIGHT-TO-VOLTAGE CONVERTER
TSL257T HIGH-SENSITIVITY LIGHT-TO-VOLTAGE CONVERTER
相關代理商/技術參數
參數描述
TSL2563CL 功能描述:光學數位轉換器 Ambient Light Sensor Light to Digital RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel
TSL2563CS 功能描述:光學數位轉換器 Ambient Light Sensor Light to Digital RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel
TSL2563FN 功能描述:光學數位轉換器 Ambient Light Sensor Light to Digital RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel
TSL2563T 功能描述:光學數位轉換器 Ambient Light Sensor Light to Digital RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel
TSL2568 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:LIGHT-TO-DIGITAL CONVERTER