參數資料
型號: TWL1110PBS
廠商: TEXAS INSTRUMENTS INC
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PQFP32
封裝: PLASTIC, QFP-32
文件頁數: 36/40頁
文件大?。?/td> 564K
代理商: TWL1110PBS
TWL1110
VOICE-BAND AUDIO PROCESSOR (VBAP
)
SLWS103 – NOVEMBER 2000
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
functional description
power on/reset
The power for the various digital and analog circuits is separated to improve the noise performance of the
device. An external reset must be applied to the active low/RESET terminal to guarantee reset upon power on
and to bring the device to an operational state. After the initial power-on sequence the device can be functionally
powered up and powered down by writing to the power control register through the I2C interface. The device
has a pin-selectable power up in the default mode option. The hardwired pin-selectable PWRUPSEL function
allows the VBAP to power up in the default mode and to be used without a microcontroller.
reference
A precision band gap reference voltage is generated internally and supplies all required voltage references to
operate the transmit and receive channels. The reference system also supplies bias voltage for use with an
electret microphone at terminal MBIAS. An external precision resistor is required for reference current setting
at terminal REXT.
I2C control interface
The I2C interface is a two-wire bidirectional serial interface. The I2C interface controls the VBAP by writing data
to seven control registers:
D Power control
D Mode control
D Transmit PGA and sidetone control
D Receive PGA gain and volume control
D DTMF routing
D Tone selection control
D Auxiliary control
There are two power up modes which may be selected at the PWRUPSEL terminal: (1) The PWRUPSEL state
(VDD at terminal 20) causes the device to power up in the default mode when power is applied. Without an I2C
interface or controlling device, the programmable functions are fixed at the default gain levels, and functions
such as the sidetone and DTMF are not accessible. (2) The PWRUPSEL state (ground at terminal 20) causes
the device to go to a power down state when power is applied. In this mode an I2C interface is required to power
up the device.
phase-locked loop (PLL)
The phase-lock loop generates the internal clock frequency required for digital filters and modulators by phase
locking to 2.048 MHz master clock input.
PCM interface
The PCM interface transmits and receives data at the PCMO and PCMI terminals respectively. The data is
transmitted or received at the PCMCLK speed once every PCMSYN cycle. The PCMCLK can be tied directly
to the 128-kHz or 2.048-MHz master clock (MCLK). The PCMSYN can be driven by an external source or
derived from the master clock and used as an interrupt to the host controller.
microphone amplifiers
The microphone input is a switchable interface for two differential microphone inputs. The first stage is a
low-noise differential amplifier that provides a gain of 23.5 dB. The second-stage amplifier has a selectable gain
of 6 or 18 dB.
相關PDF資料
PDF描述
TWL2213CAPFBR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48
TWL2214CAGQER 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA48
TWL2214CAPFB 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48
TX810IRHHT SPECIALTY ANALOG CIRCUIT, PQCC36
TX810IRHHR SPECIALTY ANALOG CIRCUIT, PQCC36
相關代理商/技術參數
參數描述
TWL1110PBSR 制造商:Rochester Electronics LLC 功能描述:- Bulk
TWL1110TQFP 制造商:TI 制造商全稱:Texas Instruments 功能描述:VOICE-BAND AUDIO PROCESSOR VBAPE
TWL1200 制造商:TI 制造商全稱:Texas Instruments 功能描述:SDIO, UART, AND AUDIO VOLTAGE-TRANSLATION TRANSCEIVER
TWL1200IPFBRQ1 功能描述:轉換 - 電壓電平 SDIO,UART,and Audio Vltg-Level Xcvr RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8
TWL1200-Q1 制造商:TI 制造商全稱:Texas Instruments 功能描述:SDIO, UART, AND AUDIO VOLTAGE-TRANSLATION TRANSCEIVER