- 您現在的位置：買賣IC網 > PDF目錄371188 > TZA1045 (NXP Semiconductors N.V.) Photodiode and amplifier IC for CD and DVD applications PDF資料下載
參數資料
| 型號： | TZA1045 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Photodiode and amplifier IC for CD and DVD applications |
| 中文描述： | 光電二極管與放大器，CD和DVD的集成電路應用技術 |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 92K |
| 代理商： | TZA1045 |
2003 Jun 26
16
Philips Semiconductors
Preliminary specification
Photodiode and amplifier IC for
CD and DVD applications
TZA1045
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certainsurfacemountICs,butitisnotsuitableforfinepitch
SMDs. In these situations reflow soldering is
recommended.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Driven by legislation and environmental forces the
worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 270
°
C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
below 220
°
C (SnPb process) or below 245
°
C (Pb-free
process)
– for all BGA and SSOP-T packages
– for packages with a thickness
≥
2.5 mm
– for packages with a thickness < 2.5 mm and a
volume
≥
350 mm
3
so called thick/large packages.
below 235
°
C (SnPb process) or below 260
°
C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250
°
C or 265
°
C, depending on solder
material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TZA1045TS | Photodiode and amplifier IC for CD and DVD applications |
| TZA3001BHL | SDH/SONET STM4/OC12 laser drivers |
| TZA3001U | SDH/SONET STM4/OC12 laser drivers |
| TZA3004 | SDH/SONET STM1/OC3 and STM4/OC12 transceiver |
| TZA3004HL | SDH/SONET data and clock recovery unit STM1/4 OC3/12 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TZA1045TS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Photodiode and amplifier IC for CD and DVD applications |
| TZA1046 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Photodiode and amplifier IC for CD and DVD applications |
| TZA1046TM | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Photodiode and amplifier IC for CD and DVD applications |
| TZA1048 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-channel BTL driver for CD/DVD drives |
| TZA1048TH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4-channel BTL driver for CD/DVD drives |
發布緊急采購，3分鐘左右您將得到回復。