- 您現在的位置：買賣IC網 > PDF目錄368687 > TZA3044BTT (NXP SEMICONDUCTORS) SDH/SONET STM4/OC12 and 1.25 Gbits/s Gigabit Ethernet postamplifiers PDF資料下載
參數資料
| 型號： | TZA3044BTT |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 通信及網絡 |
| 英文描述： | SDH/SONET STM4/OC12 and 1.25 Gbits/s Gigabit Ethernet postamplifiers |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO16 |
| 封裝： | PLASTIC, TSSOP-16 |
| 文件頁數： | 6/28頁 |
| 文件大小： | 151K |
| 代理商： | TZA3044BTT |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
1999 Nov 03
6
Philips Semiconductors
Product specification
SDH/SONET STM4/OC12 and
1.25 Gbits/s Gigabit Ethernet postamplifiers
TZA3044; TZA3044B
The relationship between the threshold current and the
detected input voltage is approximately:
(1)
In the formulas (1) and (3), the voltage on
pins DIN and DINQ is measured as peak-to-peak value.
Since the voltage on pin RSET is held constant at 1.5 V
below V
CCA
, the current flowing into this pin will be:
(2)
Combining these two formulas results in a general formula
to calculate R
ADJ
for a given input signal level detection:
(3)
Example:
Detection should occur if the differential voltage
of the input signals drops below 4 mV (p-p). In this case, a
reference current of 0.0018
×
0.004 = 7.2
μ
A should flow
into pin RSET. This can be set using a current source or
simply by connecting a resistor of the appropriate value.
The resistor must be connected between V
CCA
and
pin RSET. In this example the value would be:
0.004
The hysteresis is fixed internally at 3 dB electrical. In the
example of above, a differential level below 4 mV (p-p) of
the input signal will drive pin ST to LOW, and an input
signal level above 5.7 mV (p-p) will drive pin ST to HIGH.
A function is provided to automatically disable the signal
transmission when the chip senses that the input signal is
below the programmed threshold level. This function can
be put into operation by connecting pin JAM with pin STQ.
When the input signal is below the programmed threshold
level, the data outputs are then forced to a predetermined
state (pin DOUT = LOW and pin DOUTQ = HIGH).
Response time of the input signal level detection circuit is
determined by the time constant of the input capacitors,
together with the filter time constant (1
μ
s internal plus the
additional capacitor at pin CF). For SDH/SONET
applications couple capacitors of 1.5 nF are
recommended, leading to a high-pass frequency of
approximately 30 kHz and a maximum assert time of
30
μ
s.
Dissipation
Since the thermal resistance from junction to ambient
R
th(j-a)
of the TSSOP package is higher than the thermal
resistance of the SO package (see Chapter “Thermal
characteristics”), the dissipation should be considered
when using the TZA3044TT version.
The formula to calculate the worst case die temperature is:
(4)
where
T
j
= junction temperature
T
amb
= ambient temperature
R
th(j-a)
= thermal resistance from junction to ambient
P
max
= maximum power dissipation.
For the TZA3044T (SO package), the worst case die
temperatureT
j
= 85 + 115
×
0.3 = 119.5
°
Cwhichisbelow
the maximum operating temperature.
For the TZA3044TT (TSSOP package), the worst case die
temperature T
j
= 85 + 150
×
0.3 = 130
°
C which is higher
than the maximum operating temperature, and therefore
strongly discouraged. It is recommended to lower the
thermalresistancefromjunctiontoambient,e.g.bymeans
of a dedicated board layout.
However, if the ambient temperature is limited to 75
°
C or
the power supply is limited to 3.3
±
0.3 V, the junction
temperature will stay below the maximum value without
further precautions.
Output circuits
The output circuit of ST and STQ is given in Fig.7.
The output circuit of DOUT and DOUTQ is given in Fig.8.
Some PECL termination schemes are given in Fig.9.
I
RSET
0.0018
V
DIN
V
DINQ
–
(
)
A
[ ]
×
=
I
RSET
R
ADJ
-1.5
[ ]
=
R
ADJ
DIN
V
DINQ
)
-V
[
]
=
R
ADJ
-830
207.5 k
=
=
T
j
T
amb
R
th j
a
–
(
)
P
×
max
+
=
相關PDF資料 |
PDF描述 |
|---|---|
| TZA3044BU | SDH/SONET STM4/OC12 and 1.25 Gbits/s Gigabit Ethernet postamplifiers |
| TZA3044TT | SDH/SONET STM4/OC12 and 1.25 Gbits/s Gigabit Ethernet postamplifiers |
| TZA3044U | SDH/SONET STM4/OC12 and 1.25 Gbits/s Gigabit Ethernet postamplifiers |
| TZB4Z030AB10R00 | TRANSIL |
| TZB4Z060AB10R00 | TRANSIL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TZA3044BU | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM4/OC12 and 1.25 Gbits/s Gigabit Ethernet postamplifiers |
| TZA3044T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM4/OC12 and 1.25 Gbits/s Gigabit Ethernet postamplifiers |
| TZA3044TT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM4/OC12 and 1.25 Gbits/s Gigabit Ethernet postamplifiers |
| TZA3044U | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.25 Gbits/s Gigabit Ethernet postamplifiers |
| TZA3047A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:30 Mbits/s up to 1.25 Gbits/s laser drivers |
發布緊急采購，3分鐘左右您將得到回復。