參數資料
型號： U4084B
英文描述： Low-Voltage, Voice-Switched Circuit for Hands-Free Operation
中文描述： 低電壓，語音開關電路免提操作
文件頁數： 9/26頁
文件大小： 544K
代理商： U4084B
U4084B
Preliminary Information
TELEFUNKEN Semiconductors
Rev. A1, 31-Jan-97
9 (26)
Introduction
General
The fundamental difference between the operation of a
speakerphone and a handset is that of half-duplex versus
full-duplex. The handset is full-duplex since conversation
can occur in both directions (transmit and receive) simul-
taneously. A speakerphone has higher gain levels in both
paths, and attempting to converse full-duplex results in
oscillatory problems due to the loop that exists within the
system. The loop is formed by the receive and transmit
paths, the hybrid and the acoustic coupling (speaker to
microphone).
Today, the only practical and economical solution is to de-
sign the speakerphone in half-duplex mode, i.e., only one
person speaks at a time, while the other listens. To achieve
this, a circuit able to detect who is talking, to switch-on
the appropriate path (transmit or receive) and to switch-
off (attenuate) the other path is necessary. In this way, the
loop gain is maintained less than unity. The circuit has to
detect quickly a change from one speaker to the other and
to switch the circuit accordingly. Due to its speech-level
detectors, the circuit operates in a “hands-free” mode,
eliminating the need for a “push-to-talk” switch.
The handset has the same loop as the speakerphone.
Oscillations do not occur because the gains are consider-
ably lower, and there is almost no coupling from the
earpiece to the mouthpiece (the receiver is normally held
at a person’s ear).
The U4084B provides the level detectors, attenuators,
and switching control necessary for proper operation of
the speakerphone. The detection sensitivity and timing
are externally controllable. Additionally, the U4084B
provides background-noise monitors which make the
circuit insensitive to room and line noise, hybrid
amplifiers for interfacing to tip and ring, the microphone
amplifier, and other associated functions.
Transmit and Receive Attenuators
TI, TO and RI, RECO
The attenuators are operating complementary, i.e., when
one is at maximum gain (+6.0 dB), the other is at maxi-
mum attenuation (–46 dB), and vice versa, i.e., both are
never completely on or off. The sum of their gains re-
mains constant (within a nominal error band of
at a typical value of –40 dB (see figure 8). The attenuators
control the transmit and receive paths to provide the half-
duplex operation required in a speakerphone.
The attenuators are non-inverting, and have a –3.0 dB
(from max. gain) frequency of approximately 100 kHz.
The input impedance of each attenuator (TI and RI) is
nominally 10 k (see figure 3). To prevent distortion the
input signal should be limited to 350 mV
rms
. The maxi-
mum recommended input signal is independent from the
volume control setting. The diode clamp on the inputs
limits the input swing, and therefore the maximum nega-
tive output swing. The output impedance is less than 10
until the output current limit (typically 2.5 mA) is
reached.
11 k
0.5 dB)
C
T
12627
5 k
95 k
RI 18
TI 6
V
B
11
Figure 3. Attenuator input stage
The attenuators are controlled by the signal output of the
control block which is measurable at the C
T
pin (Pin 11).
When the C
T
pin is at +240 mV w.r.t. V
B
, the circuit is in
receive mode (the receive attenuator is at 6.0 dB). When
the C
T
pin is at –240 mV w.r.t. V
B
, the circuit is in transmit
mode (the transmit attenuator is at 6.0 dB). The circuit is
in idle mode when the C
T
voltage is equal to V
B
causing
the attenuators’ gain to be half-way between their ful-
ly-on and fully-off position (–20 dB each). Monitoring
the C
T
voltage (w.r.t. V
B
) is the most direct method of
monitoring the circuit’s mode.
The attenuator control has seven inputs: two from the
comparators operated by the level detectors, two from the
background noise monitors, volume control, dial-tone
detector, and AGC. They are described as follows:
相關PDF資料
PDF描述
U4087B Low Voltage Voice Switch Interface Circuit for Hands-free Operation in Telephone
U4087B-FP Low Voltage Voice Switch Interface Circuit for Hands-free Operation in Telephone
U4090B-N Low power dual voltage comparators
U4090B-NFN Low power dual voltage comparators
U4090B-NFNG3 Low power dual voltage comparators
相關代理商/技術參數
參數描述
U4084B-FL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Speakerphone Circuit
U4085B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Technische Daten Technical Data
U4087B 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Low Voltage Voice Switch Interface Circuit for Hands-free Operation in Telephone
U4087B-FP 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Low Voltage Voice Switch Interface Circuit for Hands-free Operation in Telephone
U4089B 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*