- 您現在的位置：買賣IC網 > PDF目錄378727 > UCC384DPTRADJ 2.5V micropower shunt voltage reference PDF資料下載
參數資料
| 型號： | UCC384DPTRADJ |
| 英文描述： | 2.5V micropower shunt voltage reference |
| 中文描述： | 工業控制IC |
| 文件頁數： | 5/19頁 |
| 文件大?。?/td> | 296K |
| 代理商： | UCC384DPTRADJ |
SLUS458C AUGUST 2001 REVISED SEPTEMBER 2003
5
www.ti.com
pin assignments
COMP:
This pin provides the output of the error amplifier for compensation. In addition, the COMP pin is
frequently used as a control port by utilizing a secondary-side error amplifier to send an error signal across the
secondary-primary isolation boundary through an opto-isolator.
CS:
The current sense pin is the non-inverting input to the PWM comparator. This is compared to a signal
proportional to the error amplifier output voltage. A voltage ramp can be applied to this pin to run the device with
a voltage mode control configuration.
FB:
This pin is the inverting input to the error amplifier. The non-inverting input to the error amplifier is internally
trimmed to 2.5 V
±
1%.
GND:
Ground return pin for the output driver stage and the logic level controller section.
OUT:
The output of the on-chip drive stage. OUT is intended to directly drive a MOSFET. The OUT pin in the
UCC38C40, UCC38C42 and UCC38C43 is the same frequency as the oscillator, and can operate near 100%
duty cycle. In the UCC38C41, UCC38C44 and the UCC38C45, the frequency of OUT is one-half that of the
oscillator due to an internal T flipflop. This limits the maximum duty cycle to < 50%.
RT/CT:
Timing resistor and timing capacitor. The timing capacitor should be connected to the device ground
using minimal trace length.
VDD:
Power supply pin for the device. This pin should be bypassed with a 0.1-
μ
F capacitor with minimal trace
lengths. Additional capacitance may be needed to provide hold up power to the device during startup.
VREF:
5-V reference. For stability, the reference should be bypassed with a 0.1-
μ
F capacitor to ground using
the minimal trace length possible.
相關PDF資料 |
PDF描述 |
|---|---|
| UCC3882DW-1 | 5-pin supervisor with watchdog timer and push-button reset |
| UCC3882DWTR | 5-pin supervisor with watchdog timer and push-button reset |
| UCC3882N | 5-pin supervisor with watchdog timer and push-button reset |
| UCC3882N-1 | 5-pin supervisor with watchdog timer and push-button reset |
| UCC3882PW | 5-pin supervisor with watchdog timer and push-button reset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC384DPTR-ADJ | 功能描述:低壓差穩壓器 - LDO 0.5A Negative Linear RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| UCC384DPTR-ADJG4 | 功能描述:低壓差穩壓器 - LDO 0.5A Negative Linear RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| UCC384-X | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Dropout 0.5A Negative Linear Regulator |
| UCC38500 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:BICMOS PFC/PWM COMBINATION CONTROLLER |
| UCC38500DW | 功能描述:功率因數校正 IC BiCMOS PFC/PWM Comb Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。