- 您現在的位置：買賣IC網 > PDF目錄379493 > UPD17225 (NEC Corp.) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER PDF資料下載
參數資料
| 型號： | UPD17225 |
| 廠商： | NEC Corp. |
| 元件分類： | 4位微控制器 |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| 中文描述： | 4位單片機的小型通用紅外遙控器 |
| 文件頁數： | 48/84頁 |
| 文件大?。?/td> | 393K |
| 代理商： | UPD17225 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
μ
PD17225, 17226, 17227, 17228
48
Data Sheet U12643EJ2V0DS00
8.3
STOP Mode
In the STOP mode, the system clock (f
X
) oscillation is stopped and the program execution is stopped to minimize current
consumption.
To set the STOP mode, use the STOP instruction.
The STOP mode releasing condition can be specified by the STOP instruction operand, as shown in Table 8-4.
After the STOP mode has released, the operation is performed as follows:
<1> Resets IRQTM.
<2> Starts the basic interval timer and watchdog timer (does not reset).
<3> Resets and starts the 8-bit timer.
<4> Executes the instruction next to [STOP 8H] when the current value of the 8-bit counter coincides with
the value of the modulo register (IRQTM is set).
The
μ
PD17225 oscillator is stopped, when the STOP instruction has been executed (i.e., in the STOP mode).
Oscillation is not resumed, until the STOP mode is released. After the STOP mode has been released, the HALT mode
is set. Set the time required to release the HALT mode by using the timer with modulo function.
The time that elapses, after the STOP mode has been released by occurrence of an interrupt, until an operation mode
is set, is shown in the following table.
8-Bit Modulo Register Set Value
(TMM)
Time Required to Set Operation Mode
after STOP Mode Release
At 4 MHz
40H
4.160 ms (64
μ
s
×
65)
FFH
16.384 ms (64
μ
s
×
256)
Remark
Set the 8-bit modulo timer before executing STOP instruction.
Caution Do not execute an instruction that clears the interrupt request flag (IRQ
×××
) for which the
interrupt enable flag (IP
×××
) is set immediately before the STOP 8H instruction; otherwise, the
STOP mode may not be set.
Table 8-4. STOP Mode Releasing Conditions
Operand Value
Releasing Conditions
1000B (08H)
When any of P0A
0
-P0A
3
and P0B
0
-P0B
3
pins goes low
Other Than Above
Setting prohibited
相關PDF資料 |
PDF描述 |
|---|---|
| UPD17225CT | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17225MC | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17226 | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17226CT | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17226GT | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD17225CT | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17225CT-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| UPD17225GT | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
| UPD17225GT-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|4-BIT|UPD17K CPU|CMOS|SOP|28PIN|PLASTIC |
| UPD17225MC | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTER |
發布緊急采購，3分鐘左右您將得到回復。