- 您現在的位置：買賣IC網 > PDF目錄378738 > UPD6129GS Remote-Control Transmitter/Encoder PDF資料下載
參數資料
| 型號： | UPD6129GS |
| 英文描述： | Remote-Control Transmitter/Encoder |
| 中文描述： | 遠程控制發射機/編碼器 |
| 文件頁數： | 18/36頁 |
| 文件大?。?/td> | 252K |
| 代理商： | UPD6129GS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
μ
PD61P24
18
17. WRITING, READING, AND VERIFYING ONE-TIME PROM (PROGRAM MEMORY)
To write, read, or verify the PROM, set the PROM mode and use the pins shown in Table 17-1. No address input
pin is used. To update the address, the clock signal input from the CLK pin is used.
Table 17-1. Pins Used to Write, Read, and Verify Program Memory
Symbol
Function
V
PP
Applies program voltage (12.5 V)
CLK
Inputs clock to update address
MD0-MD3
Selects operation mode
D0-D7
Inputs/outputs 8-bit data
V
DD
Applies supply voltage (6 V)
17.1 Operation Mode When Writing, Reading, and Verifying Program Memory
The
μ
PD61P24 enters the program memory write, read, or verify mode if +6 V is applied to the V
DD
pin and +12.5
V is applied to the V
PP
pin after the reset status has been held a certain time (V
DD
= 5 V, AC = low level).
In this mode, the operation modes listed in Table 17-2 can be selected by using the MD0 through MD3 pins.
Any input pins not used for writing, reading, or verifying the program memory must be open or connected to GND
via a pull-down resistor (470
).
Table 17-2. Operating Mode When Writing, Reading, and Verifying Program Memory
Specifies Operation Mode
Operation Mode
V
PP
V
DD
MD0
MD1
MD2
MD3
+12.5 V
+6 V
H
L
H
L
Clears program memory address to 0
L
H
H
H
Write mode
L
L
H
H
Read and verify modes
H
×
H
H
Program inhibit mode
×
: don’t care (L or H)
相關PDF資料 |
PDF描述 |
|---|---|
| UPD6130CA-002 | Remote-Control Transceiver/Endec |
| UPD61P24CS | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR REMOTE CONTROL TRANSMISSION |
| UPD61P24GS | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR REMOTE CONTROL TRANSMISSION |
| UPD6300C | MOS DIGITAL INTEGRATED CIRCUIT |
| UPD6379ALGR | 2-CHANNEL 16-BIT D/A CONVERTER FOR AUDIO APPLICATION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD6130CA-002 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Remote-Control Transceiver/Endec |
| UPD6130G-002 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Remote-Control Transceiver/Endec |
| UPD6132 | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6133 | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| UPD6133GS | 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
發布緊急采購，3分鐘左右您將得到回復。