- 您現在的位置：買賣IC網 > PDF目錄383982 > UPD6604GS (NEC Corp.) 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION PDF資料下載
參數資料
| 型號： | UPD6604GS |
| 廠商： | NEC Corp. |
| 英文描述： | 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION |
| 中文描述： | 4位單片機的紅外遙控傳輸 |
| 文件頁數： | 22/64頁 |
| 文件大?。?/td> | 268K |
| 代理商： | UPD6604GS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
22
μ
PD6604
Data Sheet U11281EJ3V0DS00
5. STANDBY FUNCTION
5.1 Outline of Standby Function
To save current consumption, two types of standby modes, i.e., HALT mode and STOP mode, are made available.
In STOP mode, the system clock stops oscillation. At this time, the OSC
IN
and OSC
OUT
pins are fixed at a low
level.
In HALT mode, CPU operation halts, while the system clock continues oscillation. When in HALT mode, the
timer (including REM output and LED output) operates.
In either STOP mode or HALT mode, the statuses of the data memory, accumulator, and port register, etc.
immediately before the standby mode is set are retained. Therefore, make sure to set the port status for the system
so that the current consumption of the whole system is suppressed before the standby mode is set.
Table 5-1. Statuses During Standby Mode
STOP Mode
HALT Mode
Setting instruction
HALT instruction
Clock oscillation circuit
Oscillation stopped
Oscillation continued
CPU
Operation halted
Data memory
Immediately preceding status retained
Operation
Accumulator
Immediately preceding status retained
statuses
Flag
F
0 (When 1, the flag is not placed in the standby mode.)
CY
Immediately preceding status retained
Port register
Immediately preceding status retained
Timer
Operation halted
(The count value is reset to “0”)
Operable
Cautions
1. Write the NOP instruction as the first instruction after STOP mode is released.
2. When standby mode is canceled, the status flag (F) is set (to 1).
3. If, at the point the standby mode has been set, its cancelation condition is met, then the
system is not placed in the standby mode. However, the status flag (F) is set (1).
相關PDF資料 |
PDF描述 |
|---|---|
| UPD6708 | IEBusa Inter Equipment Busa PROTOCOL CONTROL LSI |
| UPD6708CX | IEBusa Inter Equipment Busa PROTOCOL CONTROL LSI |
| UPD6708GS | IEBusa Inter Equipment Busa PROTOCOL CONTROL LSI |
| UPD6951 | 6 BIT D/A CONVERTER FOR VIDEO SIGNAL PROCESSING CMOS LSI |
| UPD6951C | 6 BIT D/A CONVERTER FOR VIDEO SIGNAL PROCESSING CMOS LSI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD6604GS-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|4-BIT|CMOS|SOP|20PIN|PLASTIC |
| UPD6604GS-XXX-GJG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| UPD66207F1-Y02-FN7-SES-A | 制造商:Renesas Electronics Corporation 功能描述: |
| UPD66P04AGS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
| UPD66P04AGS-GJG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。