參數資料
型號： UPD78F9211CS-CAB-A
廠商： Renesas Electronics America
文件頁數： 113/175頁
文件大小： 0K
描述： MCU 8BIT 2KB FLASH 16PIN
標準包裝： 400
系列： 78K0S/Kx1+
核心處理器： 78K0S
芯體尺寸： 8-位
速度： 10MHz
外圍設備： LVD，POR，PWM，WDT
輸入/輸出數： 13
程序存儲器容量： 2KB（2K x 8）
程序存儲器類型： 閃存
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 5.5 V
數據轉換器： A/D 4x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 16-DIP（0.300"，7.62mm）
包裝： 托盤
CHAPTER 3 CPU ARCHITECTURE
User’s Manual U16994EJ6V0UD
40
(a) Interrupt enable flag (IE)
This flag controls interrupt request acknowledge operations of the CPU.
When IE = 0, the interrupt disabled (DI) status is set. All interrupt requests are disabled.
When IE = 1, the interrupt enabled (EI) status is set. Interrupt request acknowledgment is controlled with
an interrupt mask flag for various interrupt sources.
This flag is reset to 0 upon DI instruction execution or interrupt acknowledgment and is set to 1 upon EI
instruction execution.
(b) Zero flag (Z)
When the operation result is zero, this flag is set to 1. It is reset to 0 in all other cases.
(c) Auxiliary carry flag (AC)
If the operation result has a carry from bit 3 or a borrow at bit 3, this flag is set to 1. It is reset to 0 in all
other cases.
(d) Carry flag (CY)
This flag stores overflow and underflow that have occurred upon add/subtract instruction execution. It
stores the shift-out value upon rotate instruction execution and functions as a bit accumulator during bit
operation instruction execution.
(3) Stack pointer (SP)
This is a 16-bit register to hold the start address of the memory stack area. Only the internal high-speed RAM
area can be set as the stack area (Other than the internal high-speed RAM area cannot be set as the stack
area).
Figure 3-9. Stack Pointer Configuration
0
15
SP14
SP15
SP
SP13 SP12 SP11 SP10
SP9
SP8
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
The SP is decremented before writing (saving) to the stack memory and is incremented after reading
(restoring) from the stack memory.
Each stack operation saves/restores data as shown in Figures 3-10 and 3-11.
Cautions 1.
Since reset signal generation makes the SP contents undefined, be sure to initialize the
SP before using the stack memory.
2.
Stack pointers can be set only to the high-speed RAM area, and only the lower 10 bits
can be actually set.
Thus, if the stack pointer is specified to 0FF00H, it is converted to 0FB00H in the high-
speed RAM area, since 0FF00H is in the SFR area and not in the high-speed RAM area.
When the value is actually pushed onto the stack, 1 is subtracted from 0FB00H to
become 0FAFFH, but since that value is not in the high-speed RAM area, it is converted
to 0FEFFH, which is the same value as when 0FF00H is set to the stack pointer.
相關PDF資料
PDF描述
VI-B2T-IX CONVERTER MOD DC/DC 6.5V 75W
VI-B2R-IX CONVERTER MOD DC/DC 7.5V 75W
VI-B2N-IW CONVERTER MOD DC/DC 18.5V 100W
C8051F333-GMR IC 8051 MCU 4K FLASH 20MLP
VI-B2K-IW CONVERTER MOD DC/DC 40V 100W
相關代理商/技術參數
參數描述
UPD78F9211FH-2A2-A 制造商:Renesas Electronics Corporation 功能描述:
UPD78F9211GR(T)-JJG-A 制造商:Renesas Electronics Corporation 功能描述:MCU 8-Bit 78K0S CISC 2KB Flash 5V 16-Pin SSOP
UPD78F9211GR(T)-JJG-E1-A 制造商:Renesas Electronics Corporation 功能描述:MCU 8-Bit 78K0S CISC 2KB Flash 5V 16-Pin SSOP
UPD78F9211GR-JJG-A 制造商:Renesas Electronics Corporation 功能描述:RENUPD78F9211GR-JJG-A 78K0 SEREIS MCU
UPD78F9211MA(A)-FAA-AX 制造商:Renesas Electronics Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*