參數資料
型號： UPD78P4038Y
廠商： NEC Corp.
英文描述： 16/8-BIT SINGLE-CHIP MICROCONTROLLER
中文描述： 16/8-BIT單片機
文件頁數： 22/72頁
文件大?。?/td> 435K
代理商： UPD78P4038Y
μ
PD78P4038Y
22
(1) Read mode
Set CE to L and OE to L to set read mode.
(2) Output disable mode
Set OE to H to set high impedance for data output and output disable mode.
Consequently, if several
μ
PD78P4038Y devices are connected to a data bus, the OE pins can be controlled to
select data output from any of the devices.
(3) Standby mode
Set CE to H to set standby mode.
In this mode, data output is set to high impedance regardless of the OE setting.
(4) Page data latch mode
At the beginning of page write mode, set CE to H, PGM to H, and OE to L to set page data latch mode.
In this mode, 1 page (4 bytes) of data are latched to the internal address/data latch circuit.
(5) Page write mode
After latching the address and data for one page (4 bytes) using page data latch mode, adding a 0.1 ms program
pulse (active, low) to the PGM pin with both CE and OE set to H causes page write to be executed. Later, setting
both CE and OE to L causes program verification to be executed.
If programming is not completed after one program pulse, the write and verify operations may be repeated X times
(where X
≤
10).
(6) Byte write mode
Adding a 0.1 ms program pulse (active, low) to the PGM pin with both CE and OE set to H causes byte write
to be executed. Later, setting OE to L causes program verification to be executed.
If programming is not completed after one program pulse, the write and verify operations may be repeated X times
(where X
≤
10).
(7) Program verify mode
Set CE to L, PGM to H, and OE to L to set program verify mode. Use verify mode for verification following each
write operation.
(8) Program inhibit mode
Program inhibit mode is used to write to a single device when several
μ
PD78P4038Y devices are connected in
parallel to OE , V
PP
, and D0 to D7 pins.
Use the page write mode or byte write mode described above for each write operation. Write operations cannot
be done for devices in which the PGM pin has been set to H.
相關PDF資料
PDF描述
UPD78P4038YGC-3B9 16/8-BIT SINGLE-CHIP MICROCONTROLLER
UPD78P4038YGC-8BT 16/8-BIT SINGLE-CHIP MICROCONTROLLER
UPD78P4038YGC RECTIFIER BRIDGE 1.5A 800V 40A-ifsm 1.1V-vf 5uA-ir KBP 35/TUBE
UPD8049H High-Speed, 8-Bit, Single-Chip Hmos Microcomputers
UPD8049HC High-Speed, 8-Bit, Single-Chip Hmos Microcomputers
相關代理商/技術參數
參數描述
UPD78P4038YGC-8BT-A 制造商:Renesas Electronics 功能描述:78K4 32MHz 制造商:Renesas Electronics 功能描述:78K4 32MHz Cut Tape
UPD79F8513AGB-8ES-A 制造商:Renesas Electronics Corporation 功能描述:RENUPD79F8513AGB-8ES-A 8BIT FLASH MCU
UPD800227F1-011-MN5-A 制造商:Renesas Electronics Corporation 功能描述:
UPD800232F1-012-HN2-A 制造商:Renesas Electronics Corporation 功能描述:
UPD800232F1-014-HN2-A 制造商:Renesas Electronics Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*