- 您現在的位置：買賣IC網 > PDF目錄361591 > uPSD3234AV-40T1T (意法半導體) Flash Programmable System Devices with 8032 Microcontroller Core PDF資料下載
參數資料
| 型號： | uPSD3234AV-40T1T |
| 廠商： | 意法半導體 |
| 英文描述： | Flash Programmable System Devices with 8032 Microcontroller Core |
| 中文描述： | 閃存可編程系統設備與8032微控制器內核 |
| 文件頁數： | 120/170頁 |
| 文件大小： | 2717K |
| 代理商： | UPSD3234AV-40T1T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁當前第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
uPSD3234A, uPSD3234BV, uPSD3233B, uPSD3233BV
120/170
The Port pin’s tri-state output driver enable is con-
trolled by a two input OR gate whose inputs come
from the CPLD AND Array enable product term
and the Direction Register. If the enable product
term of any of the Array outputs are not defined
and that port pin is not defined as a CPLD output
in the PSDsoft, then the Direction Register has
sole control of the buffer that drives the port pin.
The contents of these registers can be altered by
the MCU. The Port Data Buffer (PDB) feedback
path allows the MCU to check the contents of the
registers.
Ports A, B, and C have embedded Input Macro-
cells (IMC). The Input Macrocells (IMC) can be
configured as latches, registers, or direct inputs to
the PLDs. The latches and registers are clocked
by Address Strobe (ALE) or a product term from
the PLD AND Array. The outputs from the Input
Macrocells (IMC) drive the PLD input bus and can
be
read
by
the
Macrocell, page 118
.
Port Operating Modes
The I/O Ports have several modes of operation.
Some modes can be defined using PSDsoft, some
by the MCU writing to the Control Registers in
CSIOP space, and some by both. The modes that
can only be defined using PSDsoft must be pro-
grammed into the device and cannot be changed
unless the device is reprogrammed. The modes
that can be changed by the MCU can be done so
dynamically at run-time. The PLD I/O, Data Port,
Address Input, and Peripheral I/O Modes are the
only modes that must be defined before program-
ming the device. All other modes can be changed
by the MCU at run-time. See Application Note
AN1171for more detail.
Table 92., page 121
summarizes which modes
are available on each port.
Table 95., page 122
shows how and where the different modes are
configured. Each of the port operating modes are
described in the following sections.
MCU I/O Mode
In the MCU I/O Mode, the MCU uses the I/O Ports
block to expand its own I/O ports. By setting up the
CSIOP space, the ports on the PSD Module are
mapped into the MCU address space. The ad-
dresses of the ports are listed in
Table
84., page 98
.
A port pin can be put into MCU I/O Mode by writing
a '0' to the corresponding bit in the Control Regis-
ter. The MCU I/O direction may be changed by
writing to the corresponding bit in the Direction
Register, or by the output enable product term.
See
Peripheral I/O Mode, page 120
. When the pin
MCU.
See
Input
is configured as an output, the content of the Data
Out Register drives the pin. When configured as
an input, the MCU can read the port input through
the Data In buffer. See
Figure 63., page 119
.
Ports C and D do not have Control Registers, and
are in MCU I/O Mode by default. They can be used
for PLD I/O if equations are written for them in PS-
Dabel.
PLD I/O Mode
The PLD I/O Mode uses a port as an input to the
CPLD’s Input Macrocells (IMC), and/or as an out-
put from the CPLD’s Output Macrocells (OMC).
The output can be tri-stated with a control signal.
This output enable control signal can be defined
by a product term from the PLD, or by resetting the
corresponding bit in the Direction Register to '0.'
The corresponding bit in the Direction Register
must not be set to '1' if the pin is defined for a PLD
input signal in PSDsoft. The PLD I/O Mode is
specified in PSDsoft by declaring the port pins,
and then writing an equation assigning the PLD I/
O to a port.
Address Out Mode
Address Out Mode can be used to drive latched
MCU addresses on to the port pins. These port
pins can, in turn, drive external devices. Either the
output enable or the corresponding bits of both the
Direction Register and Control Register must be
set to a '1' for pins to use Address Out Mode. This
must be done by the MCU at run-time. See
Table
94., page 121
for the address output pin assign-
ments on Ports A and B for various MCUs.
Peripheral I/O Mode
Peripheral I/O Mode can be used to interface with
external peripherals. In this mode, all of Port A
serves as a tri-state, bi-directional data buffer for
the MCU. Peripheral I/O Mode is enabled by set-
ting Bit 7 of the VM Register to a '1.'
Figure
64., page 121
shows how Port A acts as a bi-di-
rectional buffer for the MCU data bus if Peripheral
I/O Mode is enabled. An equation for PSEL0 and/
or PSEL1 must be written in PSDsoft. The buffer is
tri-stated when PSEL0 or PSEL1 is low (not ac-
tive). The PSEN signal should be “ANDed” in the
PSEL equations to disable the buffer when PSEL
resides in the data space.
JTAG In-System Programming (ISP)
Port C is JTAG compliant, and can be used for In-
System Programming (ISP). For more information
on the JTAG Port, see
PROGRAMMING IN-CIR-
CUIT
USING
THE
INTERFACE, page 134
.
JTAG
SERIAL
相關PDF資料 |
PDF描述 |
|---|---|
| uPSD3234AV-40T6T | Flash Programmable System Devices with 8032 Microcontroller Core |
| UPSD3233BV | Flash Programmable System Devices with 8032 Microcontroller Core |
| uPSD3233BV-40T6T | Flash Programmable System Devices with 8032 Microcontroller Core |
| uPSD3233BV-40U1T | Flash Programmable System Devices with 8032 Microcontroller Core |
| uPSD3233BV-40U6T | Flash Programmable System Devices with 8032 Microcontroller Core |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPSD3234AV-40T6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
| UPSD3234AV-40T6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core |
| UPSD3234AV-40U1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
| UPSD3234AV-40U1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM |
| UPSD3234AV-40U6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
發布緊急采購，3分鐘左右您將得到回復。