- 您現在的位置：買賣IC網 > PDF目錄361629 > V24C48C200B (Vicor Corporation) 24Vin / 48Vout / 200Watts DC-DC Converter Module PDF資料下載
參數資料
| 型號： | V24C48C200B |
| 廠商： | Vicor Corporation |
| 元件分類： | DC/DC變換器 |
| 英文描述： | 24Vin / 48Vout / 200Watts DC-DC Converter Module |
| 中文描述： | 24Vin / 48Vout / 200Watts DC - DC轉換模塊 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 157K |
| 代理商： | V24C48C200B |
Vicor Corp.
Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
V24B48C200B DC-DC Converter
Rev. 3
Page 4 of 8
Set your site on VICOR at www.vicorpower.com
CONTROLFUNCTIONS - PC PIN
Module Enable/Disable
The module may be disabled by pulling PC below 2.3V with
respect to the
–
Input. This may be done with an open collector
transistor, relay, or optocoupler. Multiple converters may be
disabled with a single transistor or relay either directly or via
“
OR
’
ing
”
diodes. See Figure 1.
Module Alarm
The module contains
“
watchdog
”
circuitry which monitors
input voltage, operating temperature and internal operating
parameters. In the event that any of these parameters are
outside of their allowable operating range, the module will shut
down and PC will go low. PC will periodically go high and the
module will check to see if the fault (as an example,
overtemperature) has cleared. If the fault has not been cleared,
PC will go low again and the cycle will restart. The SC pin will
go low in the event of a fault and return to its normal state after
the fault has been cleared. See Figures 2 and 4.
Disable
Disable = PC <2.3V
+Out
+S
SC
–
S
–
Out
+In
PC
PR
–
In
Figure 1
—Module enable/disable.
Figure 3
—
LED on-state indicator.
4k
"Module
Enabled"
+Out
+S
SC
–
S
–
Out
+In
PC
PR
–
In
Optocoupler
+Out
+S
SC
–
S
–
Out
+In
PC
PR
–
In
4kW
Alarm
1.00V
+Out
+S
SC
–
S
–
Out
+In
PC
PR
–
In
+Out
+S
SC
–
S
–
Out
+In
PC
PR
–
In
Input Undervoltage
Input Overvoltage
Module Faults
2-f (VIN)
Auto
Restart
5.7Vdc
(0-3mA)
50
SW2
SW3
1.23
Vdc
6K
1K
SW1
SW1, 2, & 3
shown in
"Fault" position
Figure 2
—
PC/SC module alarm logic.
Figure 5
—
Isolated on-state indicator.
2-20ms typ.
Fault
SC
PC
1.23V
5.7V
40
μ
s typ.
Figure 4
—
PC/SC module alarm timing.
Figure 6
—
Secondary side on-state indicator.
Primary Auxiliary Supply
At 5.7V, PC can source up to 1.5mA. In the example shown in
Figure 3, PC powers a module enabled LED.
相關PDF資料 |
PDF描述 |
|---|---|
| V24C5C100B | 24Vin / 5Vout / 100Watts DC-DC Converter Module |
| V24H-R3-16MM-809 | KLETTVERSCHLUSS PEEK/NOMEX KLETT 3MRL |
| V24L-R3-16MM-809 | KLETTVERSCHLUSS PEEK/NOMEX FLAUSCH 3MRL |
| V24R12-12 | Analog IC |
| V5R12 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V24C48C400B | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:24Vin / 48Vout / 400Watts DC-DC Converter Module |
| V24C48C500BF | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:50 - 400W PCB MOUNTING COMPONENTS |
| V24C48C500BF2 | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:50 - 400W PCB MOUNTING COMPONENTS |
| V24C48C500BF3 | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:50 - 400W PCB MOUNTING COMPONENTS |
| V24C48C500BG | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:50 - 400W PCB MOUNTING COMPONENTS |
發布緊急采購，3分鐘左右您將得到回復。
