- 您現在的位置：買賣IC網 > PDF目錄359318 > V30218P (Electronic Theatre Controls, Inc.) Ultra Low Power 1-Bit 32 kHz RTC PDF資料下載
參數資料
| 型號： | V30218P |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Ultra Low Power 1-Bit 32 kHz RTC |
| 中文描述： | 超低功耗1位32 kHz的時鐘 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 442K |
| 代理商： | V30218P |
Test
From the various test features added to the V3021 some may be
activated by the user. Table 7a shows the test mode bits. Table 8
shows the 3 available test modes and how they can be
activated. Test mode 0 is activated by setting bit 2, address 0,
and causes all time keeping to be accelerated by 32. Test mode
1 is activated by setting bit 3, address 0, and causes all the time
and date locations, address 2 to address 9, to be incremented
in parallel at 1 Hz with no carry over (independent of each
other). The third test mode combines the previous two resulting
in parallel incrementing at 32 Hz.
An external signal generator can be used to drive the divider
chain of the V3021. Fig. 11a and 11b show how to connect the
signal generator. The speed can be increased by increasing the
signal generator frequency to a maximum of 128 kHz. An
external signal generator and test modes can be combined.
To leave test both test bits (address 0, bits 2 and 3) must be
cleared by software. Test corrupts the current time and date and
so the time and date should be reloaded after a test session.
Note :
The peak value of the signal provided by the signal
generator should not exceed 2 V on XO.
Access Considerations
The section “Communication Cycles” describes the serial data
sequences necessary to complete a communication cycle. In
common with all serial peripherals, the serial data sequences
are not re-entrant, thus a high priority interrupt, or another
software task, should not attempt to access the V3021 if it is
already in the middle of a cycle. A semaphore (software flag) on
access would allow the V3021 to be shared with other software
tasks or interrupt routines. There is no time limit on the duration
of a communication cycle and thus interrupt routines (which do
not use the V3021) can be fully executed in mid cycle without
any consequences for the V3021.
Note :
The peak value of the signal provided by the signal
generator should not exceed 2 V on XO.
Crystal Layout
In order to ensure proper oscillator operation we recommend
the following standard practices:
- Keep traces as short as possible.
- Use a guard ring around the crystal.
Fig. 12 shows the recommended layout.
10
Test Modes
Table 8
Addr. 0
bit 3
0
0
1
Addr. 0
bit 2
0
1
0
1
Normal operation
All time keeping accelerated by 32
Parallel increment of all time
data at 1 Hz with no carry over
Parallel increment of all time data
at 32 Hz with no carry over
1
Function
0 - 5.5 V
XI
XO
V3021
1)
100 k
W
1)
56 k
W
1)
indicative values
Fig. 11b
V
SS
Oscillator Layout
XI
XO
V
ss
CS
Fig. 12
V3021
Signal Generator Connection
1 - 2 V
Fig. 11a
V
SS
XI
XO
V3021
peak to peak
R
V3021
相關PDF資料 |
PDF描述 |
|---|---|
| V30218S | Ultra Low Power 1-Bit 32 kHz RTC |
| V302AS32 | High Energy Metal-Oxide Arrester Blocks |
| V31CP20 | Tubular Metal-Oxide Varistors |
| V320MTC | V320 8-Bit Registered Bus Transceiver |
| V320MTCX | Single 8-bit Bus Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V30218S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ultra Low Power 1-Bit 32 kHz RTC |
| V3021DL8A | 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:Ultra Low Power 1-Bit 32 kHz RTC |
| V3021SO8A | 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:Ultra Low Power 1-Bit 32 kHz RTC |
| V3021SO8B | 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:Ultra Low Power 1-Bit 32 kHz RTC |
| V3021XDL8A | 制造商:EMMICRO 制造商全稱:EM Microelectronic - MARIN SA 功能描述:Ultra Low Power 1-Bit 32 kHz RTC |
發布緊急采購，3分鐘左右您將得到回復。