- 您現在的位置：買賣IC網 > PDF目錄361670 > V48C12C150AN Analog IC PDF資料下載
參數資料
| 型號： | V48C12C150AN |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 153K |
| 代理商： | V48C12C150AN |
Vicor Corporation
Tel: 800-735-6200 Fax: 978-475-6715
Data Sheet: V48C12C150A DC-DC Converter
Set your site on VICOR at www.vicr.com
Date: 7-01 Rev. 3
Page 4 of 8
CONTROLFUNCTIONS - PC PIN
Module Enable/Disable
The module may be disabled by pulling PC below 2.3V with
respect to the –Input. This may be done with an open collector
transistor, relay, or optocoupler. Multiple converters may be
disabled with a single transistor or relay either directly or via
“OR’ing” diodes. See Figure 1.
Module Alarm
The module contains “watchdog” circuitry which monitors
input voltage, operating temperature and internal operating
parameters. In the event that any of these parameters are
outside of their allowable operating range, the module will shut
down and PC will go low. PC will periodically go high and the
module will check to see if the fault (as an example,
overtemperature) has cleared. If the fault has not been cleared,
PC will go low again and the cycle will restart. The SC pin will
go low in the event of a fault and return to its normal state after
the fault has been cleared. See Figures 2, 4.
Disable
Disable = PC <2.3V
+In
PC
PR
–In
Figure 1
—Module enable/disable.
Figure 3
—LED on-state indicator.
4k
"Module
Enabled"
+In
PC
PR
–In
Optocoupler
+In
PC
PR
–In
4k
Alarm
1.00V
+Out
SC
–Out
Input Undervoltage
Input Overvoltage
Over Temperature
Module Faults
2-20ms typ.
f(V
IN
)
Auto
Restart
(5.7Vdc
50
SW2
SW3
1.23
Vdc
6K
1K
SW1
SW1, 2, & 3 shown
in "Fault" position
+Out
SC
–Out
+In
PC
PR
–In
Figure 2
—PC/SC module alarm logic.
Figure 5
—Isolated on-state indicator.
2-20ms typ.
Fault
SC
PC
1.23V
5.7V
40
μ
s typ.
Figure 4
—PC/SC module alarm timing.
Figure 6
—Secondary side on-state indicator.
Primary Auxiliary Supply
At 5.7V, PC can source up to 1.5mA. In the example shown in
Figure 3, PC powers a “green” Module Enabled LED.
相關PDF資料 |
PDF描述 |
|---|---|
| V48C12C150AN2 | Model 7074-HCT Hand Crimping Tool (for Models 7074-KIT, 7074-MTR) |
| V48C12C150AN3 | Analog IC |
| V48C12C150AS | Analog IC |
| V48C12C150AS2 | Analog IC |
| V48C12C150AS3 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V48C12C150AN2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| V48C12C150AN3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| V48C12C150AS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| V48C12C150AS2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| V48C12C150AS3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。