- 您現在的位置：買賣IC網 > PDF目錄359322 > V5.5MLN41206 (Littelfuse, Inc.) Multiline Transient Voltage Surge Suppressor PDF資料下載
參數資料
| 型號： | V5.5MLN41206 |
| 廠商： | Littelfuse, Inc. |
| 英文描述： | Multiline Transient Voltage Surge Suppressor |
| 中文描述： | 多行瞬態電壓浪涌抑制器 |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 170K |
| 代理商： | V5.5MLN41206 |
Soldering Recommendations
The principal techniques used for the soldering of components in surface
mount technology are Infrared (IR) Reflow, Vapour Phase Reflow, and
Wave Soldering.Typical profiles are shown in Figures 12, 13 and 14.
When wave soldering, the MLN suppressor is attached to the circuit
board by means of an adhesive.The assembly is then placed on a con-
veyor and run through the soldering process to contact the wave. With IR
and Vapour Phase Reflow, the device is placed in a solder paste on the
substrate. As the solder paste is heated, it reflows and solders the unit to
the board.
The recommended solder for the MLN suppressor is a 62/36/2
(Sn/Pb/Ag), 60/40 (Sn/Pb), or 63/37 (Sn/Pb). Littelfuse also
recommends an RMA solder flux.
Wave soldering is the most strenuous of the processes.To avoid the
possibility of generating stresses due to thermal shock, a preheat stage
in the soldering process is recommended, and the peak temperature of
the solder process should be rigidly controlled.
Typical Performance Curves
Any Single Section (Continued)
10000
FIGURE 10. IMPEDANCE vs FREQUENCY
FIGURE 11. ADJACENT CHANNEL CROSSTALK
1000
100
10
1
0.1
1MHz
10MHz
100MHz
1GHz
10GHz
FREQUENCY
I
0
-20
-40
-60
-80
-100
-120
1kHz
100kHz
10kHz
1MHz
10MHz
100MHz
1GHz
FREQUENCY
C
V
IN
= 1V
RMS
Z = 50
When using a reflow process, care should be taken to ensure that the
MLN chip is not subjected to a thermal gradient steeper than 4 degrees
per second; the ideal gradient being 2 degrees per second. During the
soldering process, preheating to within 100 degrees of the solders peak
temperature is essential to minimize thermal shock. Examples of the sol-
dering conditions for the MLN array of suppressors are given in the
tables below.
Once the soldering process has been completed, it is still necessary to
ensure that any further thermal shocks are avoided. One possible cause of
thermal shock is hot printed circuit boards being removed from the solder
process and subjected to cleaning solvents at room temperature.The
boards must be allowed to gradually cool to less than 50
o
C before cleaning.
MLN SurgeArray
Suppressor
Surface Mount Varistors
Multiline Transient Voltage Surge Suppressor
155
www.littelfuse.com
3
S
V
Next
Previous
相關PDF資料 |
PDF描述 |
|---|---|
| V502AS32 | High Energy Metal-Oxide Arrester Blocks |
| V510LA40A | Varistor Products - Line Voltage Operation, Radial Lead |
| V510LA40AP | Varistor Products - Line Voltage Operation, Radial Lead |
| V510LA80B | Line Voltage Operation, Radial Lead |
| V510LA80BP | Varistor Products - Line Voltage Operation, Radial Lead |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V560MC03 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:LOW COST - HIGH PERFORMANCE VOLTAGE CONTROLLED OSCILLATOR |
| V560MC03-LF | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V560MC03-LF_10 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V560MC05-LF | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V560MC05-LF_10 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
發布緊急采購，3分鐘左右您將得到回復。