- 您現在的位置：買賣IC網 > PDF目錄359405 > VND600SP13TR (意法半導體) DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY PDF資料下載
參數資料
| 型號： | VND600SP13TR |
| 廠商： | 意法半導體 |
| 英文描述： | DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY |
| 中文描述： | 雙通道高側固態繼電器 |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 195K |
| 代理商： | VND600SP13TR |
8/18
VND600SP
GND
REVERSE BATTERY
Solution 1: Resistor in the ground line (R
GND
only). This
can be used with any type of load.
The following is an indication on how to dimension the
R
GND
resistor.
1) R
GND
≤
600mV / I
S(on)max
.
2) R
GND
≥ (
V
CC
) / (-I
GND
)
where -I
is the DC reverse ground pin current and can
be found in the absolute maximum rating section of the
device’s datasheet.
Power Dissipation in R
GND
(when V
CC
<0: during reverse
battery situations) is:
P
D
= (-V
CC
)
2
/R
GND
This resistor can be shared amongst several different
HSD. Please note that the value of this resistor should be
calculated with formula (1) where I
becomes the
sum of the maximum on-state currents of the different
devices.
Please note that if the microprocessor ground is not
common with the device ground then the R
will
produce a shift (I
* R
) in the input thresholds
and the status output values. This shift will vary
depending on how many devices are ON in the case of
several high side drivers sharing the same R
GND
.
PROTECTION
NETWORK
AGAINST
If the calculated power dissipation leads to a large resistor
or several devices have to share the same resistor then
the ST suggests to utilize Solution 2 (see below).
Solution 2: A diode (D
GND
) in the ground line.
A resistor (R
=1k
)
should be inserted in parallel to
D
GND
if the device will be driving an inductive load.
This small signal diode can be safely shared amongst
several different HSDs. Also in this case, the presence of
the ground network will produce a shift (
j
600mV) in the
input thresholds and the status output values if the
microprocessor ground is not common with the device
ground. This shift will not vary if more than one HSD
shares the same diode/resistor network.
Series resistor in INPUT and STATUS lines are also
required to prevent that, during battery voltage transient,
the current exceeds the Absolute Maximum Rating.
Safest configuration for unused INPUT and STATUS pin
is to leave them unconnected.
LOAD DUMP PROTECTION
D
is necessary (Voltage Transient Suppressor) if the
load dump peak voltage exceeds V
max DC rating. The
same applies if the device will be subject to transients on
the V
line that are greater than the ones shown in the
ISO T/R 7637/1 table.
1
V
CC
GND
OUTPUT2
CURRENT SENSE1
D
ld
+5V
R
prot
R
SENSE2
OUTPUT1
R
SENSE1
INPUT1
D
GND
R
GND
V
GND
CURRENT SENSE2
INPUT2
μ
C
R
prot
R
prot
R
prot
APPLICATION SCHEMATIC
相關PDF資料 |
PDF描述 |
|---|---|
| VND600PEP | DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY |
| VND600PEP13TR | DOUBLE CHANNEL HIGH SIDE SOLID STATE RELAY |
| VND7N04 | "OMNIFET": Fully Autoprotected Power MOSFET(全自動保護功率MOSFET) |
| VND810SP13TR | 20 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor |
| VND810 | DOUBLE CHANNEL HIGH SIDE DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VND600SP-E | 功能描述:功率驅動器IC 36V 25A Hi-Side SSR RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| VND600SP-E | 制造商:STMicroelectronics 功能描述:MOSFET SMART SWITCH SO-10 |
| VND600SPTR-E | 功能描述:電源開關 IC - 配電 36V 25A Hi-Side SSR RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| VND600TR-E | 功能描述:電源開關 IC - 配電 DBLE CH HI-SIDE DRVR RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| VND610SP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。