- 您現在的位置：買賣IC網 > PDF目錄300099 > VP301 (Sanyo Electric Co.,Ltd.) Ultrahigh Resolution CRT Display Video Output Amplifier for High-Voltage,Wideband Application(應用于高電壓，寬帶的超高分辨率CRT顯示視頻輸出放大器) PDF資料下載
參數資料
| 型號： | VP301 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Ultrahigh Resolution CRT Display Video Output Amplifier for High-Voltage,Wideband Application(應用于高電壓，寬帶的超高分辨率CRT顯示視頻輸出放大器) |
| 中文描述： | 超高分辨率CRT顯示器視頻放大器的高輸出電壓，寬帶應用（應用于高電壓，寬帶的超高分辨率CRT顯示器顯示視頻輸出放大器） |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 103K |
| 代理商： | VP301 |
No. 5429-4/6
VP301
Surge Protection
Surge protection is required when this device is connected to a CRT. This product requires the same protection as earlier
products.
A. Termination spark gap
B. Surge suppression resistor
C. Surge suppression diode (Installed in the vicinity of the IC output pin.)
Caution: The value of surge suppression resistors must be determined taking both the stipulated discharge test and the
required frequency bandwidth into account.
Notes on Mounting
Heat sink mounting
Since the specified heat sink is required to operate a mounted video pack, we recommend the following mounting
technique. (See the thermal design item for details on the required heat sink.) In particular, since the package used for
this product is even more compact than that used in the earlier VPA series, the following points require special care.
(These are recommendations.)
1. A tightening torque of between 39 and 58 Ncm is recommended. Note that 49 Ncm is the standard torque.
2. The bolt hole spacing in the heat sink should match that of the IC. In particular, the bolt hole spacing should be made
as close as possible, within the range that mounting is possible, to the dimensions A and B in the package
dimensions drawing, as shown below.
3. Use either the truss screws (truss bolts) or binding screws (binding bolts) stipulated in the JIS standards as the
mounting bolts. Also, use washers to protect the IC case.
4. Foreign matter, such as machining chips, must not be left trapped between the IC case and the heat sink. If grease is
applied to the junction surface, be sure to apply the grease evenly.
5. Solder the IC leads to the printed circuit board after mounting the heat sink to the IC.
Note: The heat sink is absolutely required to operate this video pack. Never, in any situation, apply power to a video pack
as an independent device. The video pack may be destroyed.
Peripheral wiring and ground leading
Inputs and outputs must be laid out as direct lines and must not cross.
If a double-sided printed circuit board is used, the output pattern must not be laid out on the other side of the printed
circuit board from the ground pattern, since this would increase the output capacitance.
IC Peripheral Pin Layout (Top view)
相關PDF資料 |
PDF描述 |
|---|---|
| VP453 | CRT Display Video Output Amplifier for High-Voltage,Wideband Application(應用于高電壓，寬帶的用于CRT顯示視頻輸出放大器) |
| VP503 | CRT Display Video Output Amplifier: High-Voltage, Wideband Amplification |
| VP513 | CRT Display Video Output Amplifier: High-Voltage, Wideband Amplification |
| VP553 | CRT Display Video Output Amplifier for High-Voltage,Wideband Application(應用于高電壓，寬帶的CRT顯示視頻輸出放大器) |
| VP603 | CRT Display Video Output Amplifier for High-Voltage,Wideband Application(應用于高電壓，寬帶的CRT顯示視頻輸出放大器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VP3-0138 | 制造商:COOPER BUSSMANN 功能描述:Ind Power Wirewound 11.2uH 20% Ferrite 1.47A T/R |
| VP3-0138-R | 功能描述:固定電感器 11.2uH 0.59A 0.061ohms RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| VP3019 | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:10/100 BASE-TX VOICE OVER IP MAGNETICS |
| VP305 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Satellite Channel Decoder |
| VP306 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Satellite Channel Decoder |
發布緊急采購，3分鐘左右您將得到回復。