THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 581-5040.
PHONE (630) 851-4722.
www.conwin.com
P R O D UC T D ATA S HE E T
Specifications subject to change without notice.
Copyright 2001 Connor-Winfield all rights reserved.
DATA SHEET #:
REV:
DATE:
PAGE
OF
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield VPLB434J3E-
S3 is a 3.3V Voltage Controlled
Crystal Oscillator (VCXO) with
LVPECL Differential outputs. Based
on fundamental strip crystal design,
the VPLB434J3E-S3 is designed for
use in Phased Lock Loop
SDH/SONET systems requiring low
jitter and tight stability. The
VPLB434J3E-S3 has a selectable
output: 155.52MHz, 166.6286MHz
or 160.5368MHZ.
1
2
VPLB434J3E-S3 - 155.52MHz
VCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
SELECTABLE OUTPUT: 155.52MHz,
166.6286MHz or 160.5368MHz
LOW PROFILE, SURFACE MOUNT
PACKAGE
3.3V SUPPLY VOLTAGE
LOW JITTER <1pS RMS
TOTAL FREQUENCY TOLERANCE: ±30ppm
TEMPERATURE RANGE: 0 to 70°C
DIFFERENTIAL LVPECL OUTPUTS
ENABLE/DISABLE FUNCTION
TAPE AND REEL PACKAGING
3.3V SURFACE MOUNT LVPECL VCXO OSCILLATOR
WITH A SELECTABLE OUTPUT FREQUENCY
VPLB434J3E-S3
Vx406
01
5/7/03
CW 0107
VPLB434J3E-S3
155.52M
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Storage Temperature
Supply Voltage
Control Voltage
OPERATING SPECIFICATIONS
PARAMETER
Center Frequency Output Select “x0 “
Center Frequency Output Select “01”
Center Frequency Output Select “11”
Total Frequency Tolerance
Operating Temperature Range
Supply Voltage
Supply Current
Jitter (BW=10Hz to 20MHz)
Jitter (BW=12kHz to 80MHz)
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
SSB Phase Noise at 100KHz offset
SSB Phase Noise at 1MHz offset
SSB Phase Noise at 10MHz offset
INPUT CHARACTERISTICS
PARAMETER
Control Voltage Range
Absolute Pull Range (APR)
Monotonic Linearity
Input Impedance
Modulation Bandwidth (3dB)
Enable Input Voltage (High)
Disable Input Voltage (Low)
Output “0” Select Voltage (Low)
Output “1” Select Voltage (High)
LOW VOLTAGE PECL OUTPUT CHARACTERISTICS
PARAMETER
LOAD
Voltage (High)
(Low)
Duty Cycle at 50% Level
Rise and Fall Times measured 20% to 80%
PACKAGE CHARACTERISTICS
Package
TABLE 1.0
NOTE
UNITS
(Vcc)
(Vc)
MINIMUM
-40
-0.5
-0.5
NOMINAL MAXIMUM
-
-
-
NOMINAL MAXIMUM
155.5200
166.6286
160.5368
-
-
3.3
-
-
-
-80
-100
-130
-135
-140
-145
NOMINAL
1.65
-
-
50K
-
-
-
-
-
NOMINAL
-
-
-
50
0.6
UNITS
°C
Vdc
Vdc
85
7.0
7.0
TABLE 2.0
NOTE
MINIMUM
-
-
-
-30
0
3.135
-
-
-
-
-
-
-
-
-
UNITS
MHz
MHz
MHz
ppm
°C
Vdc
mA
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
(Fo)
(Fo)
(Fo)
(Vcc)
(Icc)
(Vc)
(Vih)
(Vil)
“0”
“1”
-
-
-
30
70
3.465
80
5
<1
-
-
-
-
-
-
1
TABLE 3.0
NOTE
MINIMUM
0.3
+/-50
-20
-
10
>70% Vcc
-
-
>70% Vcc
MAXIMUM
3.0
20
-
-
-
<30% Vcc
<30% Vcc
-
UNITS
Vdc
ppm
%
Ohm
KHz
Vdc
Vdc
Vdc
Vdc
2
3
3
TABLE 4.0
NOTE
4
MINIMUM
-
2.275
-
45
-
MAXIMUM
50
-
1.68
55
1.0
UNITS
Ohms
Vdc
Vdc
%
nS
(Voh)
(Vol)
TABLE 5.0
Non-hermetic package consisting of an FR4 substrate with grounded met al
cover.
PROCESS RECOMMENDATIONS
Solder Reflow
TABLE 6.0
The component solder used internal to this device has a melting point of
221
°
C. The peak temperature inside the device should be less than or
equal to 220
°
C for a maximum of 10 seconds
Ultrasonic cleaning is not recommended.
Wash
Notes
1.0
Inclusive of calibration @ 25°C, frequency stability vs. temperature, power supply variation, Aging over 15 years and load
Absolute pull range (APR) is the minimum guaranteed pull range of the VCXO under all conditions over lifetime operation.
The APR is referenced to Fo. Positive Transfer Function.
The enable/disable input has an internal 75k ohm pull-down resistor.
Output terminated into 50 ohms into Vcc – 2.0Vdc or Thevenin equivalent.
2.0
3.0
4.0
Output Frequency
155.5200 MHz
166.6286 MHz
160.5368 MHz
x = does not matter
Pin 2 (S1)
x
0
1
Pin 3 (S2)
0
1
1