參數資料
型號： W19B320ABBBG
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 2M X 16 FLASH 3V PROM, 70 ns, PBGA48
封裝： 6 X 8 MM, 0.80 MM PITCH, TFBGA-48
文件頁數： 10/53頁
文件大?。?/td> 479K
代理商： W19B320ABBBG
W19B320AT/B
- 18 -
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit.
DQ5 produces “1” under these conditions which indicates that the program or erase cycle was not
successfully completed.
The device may output “1” on DQ5 if the system tries to program “1” to a location that was previously
programmed to “0.” Only the erase operation can change “0” back to “1.” Under this condition, the device
stops the operation, and while the timing limit has been exceeded, DQ5 produces “1.”
Under both these conditions, the system must write the reset command to return to the read mode (or to the
erase-suspend-read mode if a bank was previously in the erase-suspend-program mode).
6.3.7
DQ3: Sector Erase Timer
After writing a sector erasure command sequence, the system may read DQ3 to determine whether erasure
has begun or not. (The sector erase timer does not apply to the chip erase command.) The entire time-out
applies after each additional sector erasure command if additional sectors are selected for erasure. Once
the timeout period has completed, DQ3 switches from “0” to “1.” If the time between additional sector erase
commands from the system can be assumed to be less than 50
μs, the system need not monitor, DQ3 does
not need to be monitored. Please also refer to Sector Erase Command Sequence section.
After the sector erase command is written, the system should read the status of DQ7 (
#Data Polling) or
DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If
DQ3 is“1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are
ignored until the erase operation is complete. If DQ3 is “0,” the device will accept additional sector erase
commands.
The system software should check the status of DQ3 before and following each subsequent sector erase
command to ensure the command has been accepted. If DQ3 is high on the second status check, the last
command might not have been accepted.
相關PDF資料
PDF描述
W25X20-VSSI-G 2M X 1 FLASH 2.7V PROM, PDSO8
WS-512K8-70PI 512K X 8 MULTI DEVICE SRAM MODULE, 70 ns, DMA32
WS512K32-85G4TQ 2M X 8 MULTI DEVICE SRAM MODULE, 85 ns, CQFP68
WMS512K8B-25FECEA 512K X 8 STANDARD SRAM, 25 ns, CDFP32
WMS512K8B-25FEIE 512K X 8 STANDARD SRAM, 25 ns, CDFP32
相關代理商/技術參數
參數描述
W19B320ABT7H 功能描述:IC FLASH 32MBIT 70NS 48TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2
W19B320ATB 制造商:WINBOND 制造商全稱:Winbond 功能描述:4M × 8/2M × 16 BITS 3V FLEXIBLE BANK FLASH MEMORY
W19B320ATB7H 功能描述:IC FLASH 32MBIT 70NS 48TFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2
W19B320ATT7H 功能描述:IC FLASH 32MBIT 70NS 48TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:移動 SDRAM 存儲容量:256M（8Mx32） 速度:133MHz 接口:并聯 電源電壓:1.7 V ~ 1.95 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:帶卷 (TR) 其它名稱:557-1327-2
W19B320B 制造商:WINBOND 制造商全稱:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*