- 您現在的位置：買賣IC網 > PDF目錄245703 > W29S201T-55 (WINBOND ELECTRONICS CORP) 128K X 16 FLASH 5V PROM, 17 ns, PDSO48 PDF資料下載
參數資料
| 型號： | W29S201T-55 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 128K X 16 FLASH 5V PROM, 17 ns, PDSO48 |
| 封裝： | 12 X 20 MM, TSOP1-48 |
| 文件頁數： | 27/31頁 |
| 文件大?。?/td> | 253K |
| 代理商： | W29S201T-55 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁
Preliminary W29S201
Publication Release Date: April 1999
- 5 -
Revision A1
Sector Erase Operation
The three sectors, main memory and two parameters blocks, can be erased individually by initiating a
six-word command sequence. Sector address is latched on the falling WE edge of the sixth cycle while
the 30(hex) data input command is latched at the rising edge of WE. After the command loading cycle,
the device enters the internal sector erase mode, which is automatically timed and will be completed in a
fast 100 mS (typical). The host system is not required to provide any control or timing during this
operation. The device will automatically return to normal read mode after the erase operation completed.
Data polling and/or Toggle Bits can be used to detect end of erase cycle.
When the boot block lockout feature is inactivated, the boot block and the main memory block will be
erased together. Once the boot block is locked, only the main memory block will be erased by the
execution of sector erase operation.
Program Operation
The W29S201 is programmed on a word-by-word basis. Program operation can only change logical data
"1" to logical data "0" The erase operation (changed entire data in main memory and/or boot block from
"0" to "1" is needed before programming.
The program operation is initiated by a 4-word command cycle (see Command Codes for Word
Programming). The device will internally enter the program operation immediately after the word-program
command is entered. The internal program timer will automatically time-out (50
S max. - TBP) once
completed and return to normal read mode. Data polling and/or Toggle Bits can be used to detect end of
program cycle.
Hardware Data Protection
The integrity of the data stored in the W29S201 is also hardware protected in the following ways:
(1) Noise/Glitch Protection: A WE pulse of less than 15 nS in duration will not initiate a write cycle.
(2) VDD Power Up/Down Detection: The programming operation is inhibited when VDD is less than
2.5V typical.
(3) Write Inhibit Mode: Forcing OE low, CE high, or WE high will inhibit the write operation. This
prevents inadvertent writes during power-up or power-down periods.
(4) VDD power-on delay: When VDD has reached its sense level, the device will automatically time-out
5 mS before any write (erase/program) operation.
Data Polling (DQ7)- Write Status Detection
The W29S201 includes a data polling feature to indicate the end of a program or erase cycle. When the
W29S201 is in the internal program or erase cycle, any attempt to read DQ7 of the last word loaded will
receive the complement of the true data. Once the program or erase cycle is completed, DQ7 will show
the true data. Note that DQ7 will show logical "0" during the erase cycle, and become logical "1" or true
data when the erase cycle has been completed. Note that is for assynchronous read mode only
( MODE =VIH).
Toggle Bit (DQ6)- Write Status Detection
In addition to data polling, the W29S201 provides another method for determining the end of a program
cycle. During the internal program or erase cycle, any consecutive attempts to read DQ6 will produce
alternating 0's and 1's. When the program or erase cycle is completed, this toggling between 0's and 1's
相關PDF資料 |
PDF描述 |
|---|---|
| WS1M8-20FCA | 1M X 8 STANDARD SRAM, 20 ns, CDFP36 |
| WS1M8-45FM | 1M X 8 STANDARD SRAM, 45 ns, CDFP36 |
| WS1M8L-45FM | 1M X 8 STANDARD SRAM, 45 ns, CDFP36 |
| WMS128K8C-35DEIE | 128K X 8 STANDARD SRAM, 35 ns, CDSO32 |
| WE256K8150CI | 256K X 8 EEPROM 5V MODULE, 150 ns, CDIP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W2A-1819 | 制造商:Nexans 功能描述:MULTI CONDUCTORS |
| W2A21A101J4T2A | 功能描述:電容器陣列與網絡 100v 100pF 5% Tol. RoHS:否 制造商:AVX 電容:0.1 uF 容差:20 % 電壓額定值:6.3 V 元件數量:2 工作溫度范圍: 外殼長度:0.8 mm 外殼寬度:1.6 mm 外殼高度:0.5 mm 端接類型:SMD/SMT 系列:PG |
| W2A21A101KAT2A | 功能描述:電容器陣列與網絡 100v 100pF 20% Tol. RoHS:否 制造商:AVX 電容:0.1 uF 容差:20 % 電壓額定值:6.3 V 元件數量:2 工作溫度范圍: 外殼長度:0.8 mm 外殼寬度:1.6 mm 外殼高度:0.5 mm 端接類型:SMD/SMT 系列:PG |
| W2A21A220KAT2A | 功能描述:電容器陣列與網絡 100v 22pF 10% Tol. RoHS:否 制造商:AVX 電容:0.1 uF 容差:20 % 電壓額定值:6.3 V 元件數量:2 工作溫度范圍: 外殼長度:0.8 mm 外殼寬度:1.6 mm 外殼高度:0.5 mm 端接類型:SMD/SMT 系列:PG |
| W2A21A330KAT2A | 功能描述:電容器陣列與網絡 100v 33pF 10% Tol. RoHS:否 制造商:AVX 電容:0.1 uF 容差:20 % 電壓額定值:6.3 V 元件數量:2 工作溫度范圍: 外殼長度:0.8 mm 外殼寬度:1.6 mm 外殼高度:0.5 mm 端接類型:SMD/SMT 系列:PG |
發布緊急采購，3分鐘左右您將得到回復。