<menu id="zxgwg"></menu>
  • <thead id="zxgwg"><meter id="zxgwg"></meter></thead>

      1. <p id="zxgwg"></p>
        參數(shù)資料
        型號: WED7G128ATA33XDI25
        廠商: WHITE ELECTRONIC DESIGNS CORP
        元件分類: PROM
        英文描述: 64M X 16 FLASH 3.3V PROM MODULE, DMA144
        封裝: SODIMM-144
        文件頁數(shù): 3/4頁
        文件大?。?/td> 102K
        代理商: WED7G128ATA33XDI25
        3
        White Electronic Designs Corporation (508) 366-5151 www.whiteedc.com
        WED7GxxxATA33
        March 2002 Rev. A
        ECO #XXXXX
        SIGNAL DESCRIPTION
        Signal Name
        Description
        DQ0-DQ7, DQ8-DQ15
        Data bus can either be 8-bits or 16-bits wide depending on selection of CE0\ and CE1\
        CE0\, CE1\
        CE1\ always selects the odd byte of the word. CE0\ accesses the even or odd byte depending on A0 and CE1\. For 8-bit
        systems, CE0 is used and for 16-bit systems, both CE0\ and CE1\ are used. Both CE0\ and CE1\ should be decoded by the
        logic to determine the memory window.
        OE\
        This is an output enable strobe generated by the host interface. It is used to read data from the Flash ChipSet in Memory Mode
        and to read the CIS and configuration registers
        WE\
        The write enable pin is driven by the host and used for strobing data to the registers of the Flash ChipSet when the Flash
        ChipSet is configured in the memory interface mode. It is also used for writing the configuration registers.
        A0-A10
        A0-A3 selects the basic registers of the controller to communicate to the module. This requires 16 bytes of host address space.
        A0 is optional if CE0\ and CE1\ are combined to enable 16-bit wide register access.
        Busy
        The Busy signal is driven low when the product is accessing memory. When Busy is high, register access is allowed. After a
        data transfer command is issued, this signal is used to signify that the host can transfer data.
        RST
        When RST is high, the product is placed in a reset mode. This signal is only valid at power on.
        BVD1
        This signal is driven high since a battery is not used with this product
        BVD2This output line is always driven to a high state in Memory Mode since a batery is not required for this product
        IOWR
        This signal is not used in the memory mode.
        IORD
        This signal is not used in the memory mode.
        REG
        This signal is used during Memory Cycles to distinguish between common memory and register memory accesses. High for
        common memory, low for attribute memory.
        INPACK
        This signal is not used in the memory mode.
        IO16
        Optional test signals not used in the Memory Mapped Mode.
        Reserved
        Pins are reserved for future expansion and must be left floating.
        VCC
        Power pins. All VCC pins must be connected.
        VSS
        Ground pins. All VSS pins must be connected.
        NC
        No connect. Pin internally not connected.
        BLOCK DIAGRAM
        D0 - D7
        CE0
        CE1
        D8 - D15
        A0 - A10
        SanDisk
        Controller
        Data
        Control
        NAND
        Flash
        1
        2
        n
        6
        W
        E
        O
        E
        R
        S
        T
        B
        U
        S
        Y
        Control signals used
        in other modes (see
        pin list)
        相關PDF資料
        PDF描述
        WED7G512ATA33XDI25 256M X 16 FLASH 3.3V PROM MODULE, DMA144
        WMS512K8L-25CLQA 512K X 8 STANDARD SRAM, 25 ns, CQCC32
        W19B320STB9F 2M X 16 FLASH 3V PROM, 90 ns, PBGA48
        WED3DG7266V7D1I-MG 64M X 72 SYNCHRONOUS DRAM MODULE, ZMA144
        WEDPN16M64V-133B2M 16M X 64 SYNCHRONOUS DRAM, 5.5 ns, PBGA219
        相關代理商/技術參數(shù)
        參數(shù)描述
        WED7G128IDE33ADC25 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:DimmDrive Solid State IDE Flash Module with Power Failure Protection IDE36 DimmDrive Solid State IDE Flash Module IDE33
        WED7G128IDE36ADC25 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:DimmDrive Solid State IDE Flash Module with Power Failure Protection IDE36 DimmDrive Solid State IDE Flash Module IDE33
        WED7G144IDE33ADC25 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:DimmDrive Solid State IDE Flash Module with Power Failure Protection IDE36 DimmDrive Solid State IDE Flash Module IDE33
        WED7G144IDE36ADC25 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:DimmDrive Solid State IDE Flash Module with Power Failure Protection IDE36 DimmDrive Solid State IDE Flash Module IDE33
        WED7G160IDE33ADC25 制造商:WEDC 制造商全稱:White Electronic Designs Corporation 功能描述:DimmDrive Solid State IDE Flash Module with Power Failure Protection IDE36 DimmDrive Solid State IDE Flash Module IDE33