- 您現在的位置：買賣IC網 > PDF目錄371190 > X1228V14Z-2.7 (INTERSIL CORP) CONNECTOR ASSEMBLIES PDF資料下載
參數資料
| 型號： | X1228V14Z-2.7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | XO, clock |
| 英文描述： | CONNECTOR ASSEMBLIES |
| 中文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO14 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MO-153AC, TSSOP-14 |
| 文件頁數： | 10/31頁 |
| 文件大?。?/td> | 569K |
| 代理商： | X1228V14Z-2.7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
X1228
REV 1.3 3/24/04
Characteristics subject to change without notice.
10 of 31
www.xicor.com
The control bits for this function are FO1 and FO0 and
are found in address 0011h of the Clock Control Mem-
ory map. See “Programmable Frequency Output
Bits—FO1, FO0” on page 14.
X1, X2
The X1 and X2 pins are the input and output,
respectively, of an inverting amplifier. An external
32.768kHz quartz crystal is used with the X1228 to
supply a timebase for the real time clock. The
recommended crystal is a Citizen CFS206-32.768KDZF.
Internal compensation circuitry is included to form a
complete oscillator circuit. Care should be taken in the
placement of the crystal and the layout of the circuit.
Plenty of ground plane around the device and short
traces to X1 and X2 are highly recommended. See
Application section for more recommendations.
Figure 1. Recommended Crystal connection
POWER CONTROL OPERATION
The power control circuit accepts a V
CC
and a V
BACK
input. The power control circuit power the clock from
V
BACK
when V
CC
< V
BACK
- 0.2V. It will switch back to
power the device from V
CC
when V
CC
exceeds V
BACK
.
Figure 2. Power Control
REAL TIME CLOCK OPERATION
The Real Time Clock (RTC) uses an external
32.768kHz quartz crystal to maintain an accurate inter-
nal representation of the second, minute, hour, day,
date, month, and year. The RTC has leap-year correc-
tion. The clock also corrects for months having fewer
than 31 days and has a bit that controls 24 hour or AM/
PM format. When the X1228 powers up after the loss
of both V
CC
and V
BACK
, the clock will not operate until
at least one byte is written to the clock register.
Reading the Real Time Clock
The RTC is read by initiating a Read command and
specifying the address corresponding to the register of
the Real Time Clock. The RTC Registers can then be
read in a Sequential Read Mode. Since the clock runs
continuously and a read takes a finite amount of time,
there is the possibility that the clock could change during
the course of a read operation. In this device, the time is
latched by the read command (falling edge of the clock on
the ACK bit prior to RTC data output) into a separate latch
to avoid time changes during the read operation. The
clock continues to run. Alarms occurring during a read
are unaffected by the read operation.
Writing to the Real Time Clock
The time and date may be set by writing to the RTC
registers. To avoid changing the current time by an
uncompleted write operation, the current time value is
loaded into a separate buffer at the falling edge of the
clock on the ACK bit before the RTC data input bytes,
the clock continues to run. The new serial input data
replaces the values in the buffer. This new RTC value
is loaded back into the RTC Register by a stop bit at
the end of a valid write sequence. An invalid write oper-
ation aborts the time update procedure and the con-
tents of the buffer are discarded. After a valid write
operation the RTC will reflect the newly loaded data
beginning with the next “one second” clock cycle after
the stop bit is written. The RTC continues to update the
time while an RTC register write is in progress and the
RTC continues to run during any nonvolatile write
sequences. A single byte may be written to the RTC
without affecting the other bytes.
Accuracy of the Real Time Clock
The accuracy of the Real Time Clock depends on the
frequency of the quartz crystal that is used as the time
base for the RTC. Since the resonant frequency of a
crystal is temperature dependent, the RTC perfor-
mance will also be dependent upon temperature. The
frequency deviation of the crystal is a fuction of the
turnover temperature of the crystal from the crystal’s
nominal frequency. For example, a >20ppm frequency
deviation translates into an accuracy of >1 minute per
month. These parameters are available from the
crystal manufacturer. Xicor’s RTC family provides on-
chip crystal compensation networks to adjust load-
capacitance to tune oscillator frequency from +116
ppm to –37 ppm when using a 12.5 pF load crystal.
For
more detail information see the Application section.
X1
X2
V
BACK
In
Voltage
V
CC
On
Off
相關PDF資料 |
PDF描述 |
|---|---|
| X1228S14Z-2.7A | EXT. DISTANCE DATA CABLE 16 CO |
| X1228S14-4.5A | RTC Module With CPU Supervisor |
| X1228V14-4.5A | RTC Module With CPU Supervisor |
| X1228S14IZ-2.7 | RTC Module With CPU Supervisor |
| X1228V14IZ-2.7 | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1228V14Z-4.5A | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1228ZY WAF | 制造商:Intersil Corporation 功能描述: |
| X122K | 制造商:IQD Frequency Products 功能描述:CRYSTAL OSCILLATOR 12.288000MHZ |
| X122-SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| X123-133.33M | 制造商:CONNOR-WINFIELD 制造商全稱:Connor-Winfield Corporation 功能描述:5.0x7.0mm Surface Mount LVCMOS Clock Oscillator Series |
發布緊急采購，3分鐘左右您將得到回復。