- 您現在的位置：買賣IC網 > PDF目錄371191 > X1288S16-2.7 RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X1288S16-2.7 |
| 元件分類： | CPU監測 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 17/31頁 |
| 文件大小： | 560K |
| 代理商： | X1288S16-2.7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
17 of 31
REV 1.1.30 3/24/04
www.xicor.com
Preliminary Information
X1288
Watchdog Timer Restart
The Watchdog Timer is started by a falling edge of
SDA when the SCL line is high and followed by a stop
bit. The start signal restarts the watchdog timer
counter, resetting the period of the counter back to the
maximum. If another start fails to be detected prior to
the watchdog timer expiration, then the RESET pin
becomes active. In the event that the start signal
occurs during a reset time out period, the start will
have no effect. When using a single START to refresh
watchdog timer, a STOP bit should be followed to reset
the device back to stand-by mode.
LOW VOLTAGE RESET OPERATION
When a power failure occurs, and the voltage to the
part drops below a fixed v
TRIP
voltage, a reset pulse is
issued to the host microcontroller. The circuitry moni-
tors the V
CC
line with a voltage comparator which
senses a preset threshold voltage. Power up and
power down waveforms are shown in Figure 5. The
Low Voltage Reset circuit is to be designed so the
RESET signal is valid down to 1.0V.
When the low voltage reset signal is active, the opera-
tion of any in progress nonvolatile write cycle is unaf-
fected, allowing a nonvolatile write to continue as long
as possible (down to the power on reset voltage). The
low voltage reset signal, when active, terminates in
progress communications to the device and prevents
new commands, to reduce the likelihood of data cor-
ruption.
V
CC
THRESHOLD RESET PROCEDURE [Optional]
The X1288 is shipped with a standard V
CC
threshold
(V
TRIP
) voltage. This value will not change over normal
operating and storage conditions. However, in applica-
tions where the standard V
TRIP
is not exactly right, or if
higher precision is needed in the V
TRIP
value, the
X1288 threshold may be adjusted. The procedure is
described below, and uses the application of a nonvol-
atile write control signal.
Setting the V
TRIP
Voltage
It is necessary to reset the trip point before setting the
new value.
To set the new V
TRIP
voltage, apply the desired V
TRIP
threshold voltage to the V
CC
pin and tie the RESET pin
to the programming voltage V
P
. Then write data 00h to
address 01h. The stop bit following a valid write opera-
tion initiates the V
TRIP
programming sequence. Bring
RESET to V
CC
to complete the operation.
Note:
this
operation may take up to 10 milliseconds to complete
and also writes 00h to address 01h of the EEPROM
array.
Resetting the V
TRIP
Voltage
This procedure is used to set the V
TRIP
to a “native”
voltage level. For example, if the current V
TRIP
is 4.4V
and the new V
TRIP
must be 4.0V, then the V
TRIP
must
be reset. When V
TRIP
is reset, the new V
TRIP
is some-
thing less than 1.7V. This procedure must be used to
set the voltage to a lower value.
Figure 4. Watchdog Restart/Time Out
t
RSP
<t
WDO
t
RST
RESET
SDA
t
RSP
Note:
All inputs are ignored during the active reset period (t
RST
).
t
RST
SCL
t
RSP
>t
WDO
t
RSP
>t
WDO
Start
Stop
Start
相關PDF資料 |
PDF描述 |
|---|---|
| X1288S16-2.7A | RTC Module With CPU Supervisor |
| X1288S16I | RTC Module With CPU Supervisor |
| X1288S16I-2.7 | RTC Module With CPU Supervisor |
| X1288S16I-2.7A | RTC Module With CPU Supervisor |
| X1288S16I-4.5A | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1288S16-4.5A | 功能描述:IC RTC/CAL/CPU SUP EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1288S16-4.5AT1 | 功能描述:IC RTC/CAL/CPU SUP EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1288S16I | 功能描述:IC RTC/CAL/CPU SUP EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1288S16I-2.7 | 功能描述:IC RTC/CAL/CPU SUP EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1288S16I-2.7A | 功能描述:IC RTC/CAL/CPU SUP EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。