- 您現在的位置：買賣IC網 > PDF目錄371191 > X1288V14-2.7A RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X1288V14-2.7A |
| 元件分類： | CPU監測 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 11/31頁 |
| 文件大?。?/td> | 560K |
| 代理商： | X1288V14-2.7A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
11 of 31
REV 1.1.30 3/24/04
www.xicor.com
Preliminary Information
X1288
When used as frequency output, this signal has a fre-
quency of 32.768kHz, 100Hz, 1Hz or inactive.
When used as interrupt output, this signal notifies a
host processor that an alarm has occurred and an
action is required. It is an active LOW output.
The control bits for this function are FO1 and FO0 and
are found in address 0011h of the Clock Control Mem-
ory map.
See “Programmable Frequency Output Bits—
FO1, FO0” on page 15.
X1, X2
The X1 and X2 pins are the input and output,
respectively, of an inverting amplifier. An external
32.768kHz quartz crystal is used with the X1288 to
supply a timebase for the real time clock. The
recommended crystal is a Citizen CFS206-32.768KDZF.
Internal compensation circuitry is included to form a
complete oscillator circuit. Care should be taken in the
placement of the crystal and the layout of the circuit.
Plenty of ground plane around the device and short
traces to X1 and X2 are highly recommended. See
Application section for more information.
Figure 2. Recommended Crystal connection
POWER CONTROL OPERATION
The power control circuit accepts a V
CC
and a V
BACK
input. The power control circuit powers the clock from
V
BACK
when V
CC
< V
BACK
- 0.2V. It will switch back to
power the device from V
CC
when V
CC
exceeds V
BACK
.
Figure 3. Power Control
REAL TIME CLOCK OPERATION
The Real Time Clock (RTC) uses an external
32.768kHz quartz crystal to maintain an accurate inter-
nal representation of the 1/100 of a second, second,
minute, hour, day, date, month, and year. The RTC has
leap-year correction. The clock also corrects for
months having fewer than 31 days and has a bit that
controls 24 hour or AM/PM format. When the X1288
powers up after the loss of both V
CC
and V
BACK
, the
clock will not operate until at least one byte is written to
the clock register.
Reading the Real Time Clock
The RTC is read by initiating a Read command and
specifying the address corresponding to the register of
the Real Time Clock. The RTC Registers can then be
read in a Sequential Read Mode. Since the clock runs
continuously and a read takes a finite amount of time,
there is the possibility that the clock could change during
the course of a read operation. In this device, the time is
latched by the read command (falling edge of the clock on
the ACK bit prior to RTC data output) into a separate latch
to avoid time changes during the read operation. The
clock continues to run. Alarms occurring during a read
are unaffected by the read operation.
Writing to the Real Time Clock
The time and date may be set by writing to the RTC
registers. To avoid changing the current time by an
uncompleted write operation, the current time value is
loaded into a separate buffer at the falling edge of the
clock on the ACK bit before the RTC data input bytes,
the clock continues to run. The new serial input data
replaces the values in the buffer. This new RTC value
is loaded back into the RTC Register by a stop bit at
the end of a valid write sequence. An invalid write
operation aborts the time update procedure and the
contents of the buffer are discarded. After a valid write
operation the RTC will reflect the newly loaded data
beginning with the SSEC register reset to “0” at the
next sub-second update after the stop bit is written.
The 1Hz frequency output from the PHZ/IRQ pin will
be reset to restart after the stop bit is written. The RTC
continues to update the time while an RTC register
write is in progress and the RTC continues to run dur-
ing any nonvolatile write sequences. A single byte may
be written to the RTC without affecting the other bytes.
Accuracy of the Real Time Clock
The accuracy of the Real Time Clock depends on the
frequency of the quartz crystal that is used as the time
base for the RTC. Since the resonant frequency of a
crystal is temperature dependent, the RTC performance
will also be dependent upon temperature. The frequency
deviation of the crystal is a function of the turnover
temperature of the crystal from the crystal’s nominal
X1
X2
V
BACK
In
Voltage
V
CC
On
Off
相關PDF資料 |
PDF描述 |
|---|---|
| X1288V14-4.5A | RTC Module With CPU Supervisor |
| X1288V14I | RTC Module With CPU Supervisor |
| X1288V14I-2.7 | RTC Module With CPU Supervisor |
| X1288V14I-2.7A | RTC Module With CPU Supervisor |
| X1288V14I-4.5A | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X1288V14-4.5A | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1288V14-4.5AT1 | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1288V14I | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1288V14I-2.7 | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| X1288V14I-2.7A | 功能描述:IC RTC/CAL/CPU SUP EE 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。