- 您現在的位置：買賣IC網 > PDF目錄371196 > X24001MI-2.7 Identi⑩PROM PDF資料下載
參數資料
| 型號： | X24001MI-2.7 |
| 英文描述： | Identi⑩PROM |
| 中文描述： | 認⑩胎膜早破 |
| 文件頁數： | 2/13頁 |
| 文件大小： | 47K |
| 代理商： | X24001MI-2.7 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
2
X24001
PIN DESCRIPTIONS
Serial Clock (SCL)
The SCL input is used to clock all data into and out of the
device.
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into and
out of the device. It is a push/pull output and does not
require the use of a pull-up resistor. During the program-
ming operation, SDA is an input.
PIN NAMES
Symbol
NC
V
SS
V
CC
SDA
SCL
Description
No Connect
Ground
Supply Voltage
Serial Data
Serial Clock
3830 PGM T01
DEVICE OPERATION
The X24001 supports a bidirectional bus oriented proto-
col. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as
the receiver. The device controlling the transfer is a
master and the device being controlled is the slave. The
master will always initiate data transfers and provide the
clock for both transmit and receive operations. There-
fore, the X24001 will be considered a slave in all appli-
cations.
Clock and Data Conventions
Data states on the SDA line can change only during SCL
LOW. SDA state changes during SCL HIGH are re-
served for indicating start and stop conditions. Refer to
Figures 1 and 2.
Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL is
HIGH. The X24001 continuously monitors the SDA and
SCL lines for the start condition and will not respond to
any command until this condition has been met.
A start may be issued to terminate the input of a control
word or the input of data to be written. This will reset the
device and leave it ready to begin a new read or write
command. Because of the push/pull output, a start
cannot be generated while the part is outputting data.
Starts are also inhibited while a write is in progress.
Stop Condition
The stop condition is a LOW to HIGH transition of SDA
when SCL is HIGH. The stop condition is used to reset
the device during a command or data input sequence
and will leave the device in the standby mode. As with
starts, stops are inhibited when outputting data and
while a write is in progress.
相關PDF資料 |
PDF描述 |
|---|---|
| X24001MI-3 | Identi⑩PROM |
| X24001MM-2.7 | Identi⑩PROM |
| X24001MM-3 | Identi⑩PROM |
| X24001 | Solid State Relay PCB Mount |
| X24001M | Identi⑩PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X24001MI-3 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
| X24001MM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
| X24001MM-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
| X24001MM-3 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
| X24001P | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
發布緊急采購，3分鐘左右您將得到回復。