- 您現在的位置：買賣IC網 > PDF目錄371197 > X24001SM-2.7 Identi⑩PROM PDF資料下載
參數資料
| 型號： | X24001SM-2.7 |
| 英文描述： | Identi⑩PROM |
| 中文描述： | 認⑩胎膜早破 |
| 文件頁數： | 2/13頁 |
| 文件大?。?/td> | 47K |
| 代理商： | X24001SM-2.7 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
2
X24001
PIN DESCRIPTIONS
Serial Clock (SCL)
The SCL input is used to clock all data into and out of the
device.
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into and
out of the device. It is a push/pull output and does not
require the use of a pull-up resistor. During the program-
ming operation, SDA is an input.
PIN NAMES
Symbol
NC
V
SS
V
CC
SDA
SCL
Description
No Connect
Ground
Supply Voltage
Serial Data
Serial Clock
3830 PGM T01
DEVICE OPERATION
The X24001 supports a bidirectional bus oriented proto-
col. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as
the receiver. The device controlling the transfer is a
master and the device being controlled is the slave. The
master will always initiate data transfers and provide the
clock for both transmit and receive operations. There-
fore, the X24001 will be considered a slave in all appli-
cations.
Clock and Data Conventions
Data states on the SDA line can change only during SCL
LOW. SDA state changes during SCL HIGH are re-
served for indicating start and stop conditions. Refer to
Figures 1 and 2.
Start Condition
All commands are preceded by the start condition,
which is a HIGH to LOW transition of SDA when SCL is
HIGH. The X24001 continuously monitors the SDA and
SCL lines for the start condition and will not respond to
any command until this condition has been met.
A start may be issued to terminate the input of a control
word or the input of data to be written. This will reset the
device and leave it ready to begin a new read or write
command. Because of the push/pull output, a start
cannot be generated while the part is outputting data.
Starts are also inhibited while a write is in progress.
Stop Condition
The stop condition is a LOW to HIGH transition of SDA
when SCL is HIGH. The stop condition is used to reset
the device during a command or data input sequence
and will leave the device in the standby mode. As with
starts, stops are inhibited when outputting data and
while a write is in progress.
相關PDF資料 |
PDF描述 |
|---|---|
| X24001SM-3 | Identi⑩PROM |
| X24001M-2.7 | Identi⑩PROM |
| X24001M-3 | Identi⑩PROM |
| X24001PI-2.7 | Identi⑩PROM |
| X24001SI-2.7 | Identi⑩PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X24001SM-3 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Identi⑩PROM |
| X24-009-DK | 功能描述:射頻開發工具 2.4 GHz - Xstream 9600 BAUD RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
| X24-009-DK-INT | 制造商:Digi International 功能描述:XSTREAM DEVELOPMENT KIT, 2.4GHZ, 50MW, 9600 BAUD, 3" WIRE & - Boxed Product (Development Kits) 制造商:Digi International Inc 功能描述:KIT DEV XSTREAM 2.4GHZ 50MW 制造商:Digi International Inc 功能描述:Xstream Dev Kit 制造商:Digi International 功能描述:Xstream 2.4GHz Modem Dev kit 9600 Baud |
| X24-009NMC | 功能描述:射頻模塊 2.4 GHz - Xsstream 9600 BAUD RoHS:否 制造商:Linx Technologies 產品:Transceiver Modules 頻帶:902 MHz to 928 MHz 輸出功率:- 15.5 dBm to + 12.5 dBm 接口類型:UART 工作電源電壓:- 0.3 VDC to + 5.5 VDC 傳輸供電電流:38.1 mA 接收供電電流:22.7 mA 天線連接器類型:U.FL 最大工作溫度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| X24-009NMI | 功能描述:射頻模塊 24XStream 50mW tran er w/MMCX 9600 bps RoHS:否 制造商:Linx Technologies 產品:Transceiver Modules 頻帶:902 MHz to 928 MHz 輸出功率:- 15.5 dBm to + 12.5 dBm 接口類型:UART 工作電源電壓:- 0.3 VDC to + 5.5 VDC 傳輸供電電流:38.1 mA 接收供電電流:22.7 mA 天線連接器類型:U.FL 最大工作溫度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
發布緊急采購，3分鐘左右您將得到回復。