參數資料
型號： X24320S8I-1.8
英文描述： 400KHz 2-Wire Serial E2PROM with Block Lock
中文描述： 400kHz的2線串行E2PROM的塊鎖
文件頁數： 8/17頁
文件大小： 85K
代理商： X24320S8I-1.8
X24320
8
Random Read
Random read operation allows the master to access
any memory location in the array. Prior to issuing the
Slave Address Byte with the R/W bit set to one, the
master must first perform a “Dummy” write operation.
The master issues the start condition and the Slave
Address Byte with the R/W bit low, receives an
acknowledge, then issues the Word Address Byte 1,
receives another acknowledge, then issues the Word
Address Byte 0. After the device acknowledges receipt
of the Word Address Byte 0, the master issues another
start condition and the Slave Address Byte with the
R/W bit set to one. This is followed by an acknowledge
and then eight bits of data from the device. The master
terminates the read operation by not responding with
an acknowledge and then issuing a stop condition.
Refer to figure 9 for the address, acknowledge, and
data transfer sequence.
The device will perform a similar operation called “Set
Current Address” if a stop is issued instead of the
second start shown in figure 9. The device will go into
standby mode after the stop and all bus activity will be
ignored until a start is detected. The effect of this oper-
ation is that the new address is loaded into the
address counter, but no data is output by the device.
The next Current Address Read operation will read
from the newly loaded address.
Sequential Read
Sequential reads can be initiated as either a current
address read or random read. The first Data Byte is
transmitted as with the other modes; however, the
master now responds with an acknowledge, indicating
it requires additional data. The device continues to
output data for each acknowledge received. The
master terminates the read operation by not
responding with an acknowledge and then issuing a
stop condition.
The data output is sequential, with the data from address
n followed by the data from address n + 1. The address
counter for read operations increments through all byte
addresses, allowing the entire memory contents to be
read during one operation. At the end of the address
space the counter “rolls over” to address 0000h and the
device continues to output data for each acknowledge
received. Refer to figure 10 for the acknowledge and
data transfer sequence.
SLAVE
ADDRESS
S
S
T
O
P
P
A
C
K
A
C
K
A
C
K
A
C
K
DATA
(1)
DATA
(2)
SIGNALS
FROM THE
MASTER
SDA BUS
SIGNALS
FROM THE
SLAVE
DATA
(n–1)
DATA
(n)
1
(n is any integer greater than 1)
7035 FM 12
SIGNALS
FROMTHE
MASTER
SDA BUS
SIGNALS
FROMTHE
SLAVE
S
T
A
R
T
S
SLAVE
ADDRESS
S
T
O
P
P
A
C
K
A
C
K
A
C
K
WORDADDRESS
BYTE 1
SLAVE
ADDRESS
0
WORD ADDRESS
BYTE 0
S
T
A
R
T
S
1
DATA
A
C
K
1 0 1 0
7035 FM 11
Figure 9. Random Read Sequence
Figure 10. Sequential Read Sequence
相關PDF資料
PDF描述
X24320S8I-2.5 Series 940-F/947, 3000 mm [118.0 in] scan distance, Plastic M30, Prewired 2 m, switching output PNP, adjustment potentiometer
X24320P-2.5 400KHz 2-Wire Serial E2PROM with Block Lock
X24321S8I-1.8 400 KHz 2-Wire Serial E2PROM
X24321 400 KHz 2-Wire Serial E2PROM
X24321S8 400 KHz 2-Wire Serial E2PROM
相關代理商/技術參數
參數描述
X24320S8I-2.5 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:400KHz 2-Wire Serial E2PROM with Block Lock
X24320S8IG 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:400KHz 2-Wire Serial E2PROM with Block Lock
X24320S8IG-1.8 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:400KHz 2-Wire Serial E2PROM with Block Lock
X24320S8IG-2.5 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:400KHz 2-Wire Serial E2PROM with Block Lock
X24320V 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:400KHz 2-Wire Serial E2PROM with Block Lock
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*