- 您現在的位置：買賣IC網 > PDF目錄371201 > X24645 Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection PDF資料下載
參數資料
| 型號： | X24645 |
| 英文描述： | Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection |
| 中文描述： | 先進的2線串行e的2座門鎖TM保護胎膜早破 |
| 文件頁數： | 7/18頁 |
| 文件大小： | 84K |
| 代理商： | X24645 |
X24645
7
Figure 7. Current Address Read
Figure 8. Random Read
READ OPERATIONS
Read operations are initiated in the same manner as
write operations with the exception that the R/
the slave address is set HIGH. There are three basic
read operations: current address read, random read
and sequential read.
W
bit of
It should be noted that the ninth clock cycle of the read
operation is not a “don’t care.” To terminate a read op-
eration, the master must either issue a stop condition
during the ninth cycle or hold SDA HIGH during the
ninth clock cycle and then issue a stop condition.
Current Address Read
Internally the X24645 contains an address counter that
maintains the address of the last byte read, increment-
ed by one or the exact address of the last byte written.
Therefore, if the last access read was to address n, the
next read operation would access data from address
n + 1. Upon receipt of the slave address with the R/W
set HIGH, the X24645 issues an acknowledge and
transmits the byte. The read operation is terminated by
the master; by not responding with an acknowledge
and by issuing a stop condition. Refer to Figure 7 for the
sequence of address, acknowledge and data transfer.
Random Read
Random read operations allow the master to access
any memory location in a random manner. Prior to issu-
ing the slave address with the R/W bit set HIGH, the
master must first perform a “dummy” write operation.
The master issues the start condition, and the slave ad-
dress with the R/W bit set LOW, followed by the byte
address it is to read. After the word address acknowl-
edge, the master immediately reissues the start condi-
tion and the slave address with the R/W bit set HIGH.
This will be followed by an acknowledge from the
X24645 and then by the data byte. The read operation
is terminated by the master; by not responding with an
acknowledge and by issuing a stop condition. Refer to
Figure 8 for the address, acknowledge and data trans-
fer sequence.
BUS ACTIVITY:
MASTER
SDA LINE
BUS ACTIVITY:
X24645
S
T
A
R
T
SLAVE
ADDRESS
S
S
T
O
P
P
A
C
K
DATA
2783 ILL F11
BUS ACTIVITY:
MASTER
SDA LINE
BUS ACTIVITY:
X24645
S
T
A
R
T
SLAVE
ADDRESS
S
A
C
K
2783 ILL F12.1
S
T
A
R
T
S
BYTE
ADDRESS n
A
C
K
SLAVE
ADDRESS
DATA n
A
C
K
S
T
O
P
P
相關PDF資料 |
PDF描述 |
|---|---|
| X24645P | Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection |
| X24645P-2.7 | Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection |
| X24645PI | Advanced 2-Wire Serial E 2 PROM with Block Lock TM Protection |
| X24645S8-2.7 | ; For Use With:SC4505 Boost Converter |
| X24645S8I | Controller IC; Package/Case:12-MLPQ; Supply Voltage Max:15V; Features:Synchronous Buck/Buck-Boost, Current Mode, Low Voltage; Leaded Process Compatible:Yes; Operating Temp. Max:150 C; Operating Temp. Min:-40 C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X246458I-2.7TI | 制造商:Intersil Corporation 功能描述: |
| X24645A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| X24645A-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| X24645AI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| X24645AI-2.7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。