- 您現在的位置：買賣IC網 > PDF目錄371211 > X25043PI-2.7 Programmable Watchdog Supervisory E2PROM PDF資料下載
參數資料
| 型號： | X25043PI-2.7 |
| 英文描述： | Programmable Watchdog Supervisory E2PROM |
| 中文描述： | 可編程看門狗監控E2PROM的 |
| 文件頁數： | 4/15頁 |
| 文件大?。?/td> | 93K |
| 代理商： | X25043PI-2.7 |
X25043/45
4
Clock and Data Timing
Data input on the SI line is latched on the rising edge of
SCK. Data is output on the SO line by the falling edge of
SCK.
Read Sequence
When reading from the E
2
PROM memory array,
CS
is
first pulled LOW to select the device. The 8-bit READ
instruction is transmitted to the X25043/45, followed by
the 8-bit byte address. Bit 3 of the Read instruction
contains address A
8
. This bit is used to select the upper
or lower half of the device. After the read opcode and
byte address are sent, the data stored in the memory
at the selected address is shifted out on the SO line.
The data stored in memory at the next address can be
read sequentially by continuing to provide clock pulses.
The byte address is automatically incremented to the
next higher address after each byte of data is shifted
out. When the highest address is reached ($1FF) the
address counter rolls over to address $000, allowing
the read cycle to be continued indefinitely. The read
operation is terminated by taking
CS
HIGH. Refer to the
read E
2
PROM Array operation sequence illustrated in
Figure 1.
To read the status register the
CS
line is first pulled
LOW to select the device followed by the 8-bit RDSR
instruction. After the read status register opcode is
sent, the contents of the status register is shifted out on
the SO line as shown in Figure 2.
Write Sequence
Prior to any attempt to write data into the X25043/45 the
“write enable” latch must first be set by issuing
the WREN instruction (See Figure 3).
CS
is first taken
LOW, then the WREN instruction is clocked into the
X25043/45. After all eight bits of the instruction are
transmitted,
CS
must then be taken HIGH. If the user
continues the write operation without taking
CS
HIGH
after issuing the WREN instruction the write operation
will be ignored.
To write data to the E
2
PROM memory array, the user
issues the WRITE instruction, followed by the address
and then the data to be written. Bit 3 of the Write
instruction contains address A
8
. This bit is used to select
the upper or lower half of the device. This is minimally a
twenty-four clock operation.
CS
must go LOW and
remain LOW for the duration of the operation. The host
may continue to write up to four bytes of data to the
X25043/45. The only restriction is the four bytes must
reside on the same page. A page address begins with
address X XXXX XX00 and ends with X XXXX XX11. If
the byte address counter reaches X XXXX XX11 and the
clock continues the counter will roll back to the first
address of the page and overwrite any data that may
have been written.
For the write operation (byte or page write) to be
completed,
CS
can only be brought HIGH after the
twenty-fourth, thirty-second, fortieth, or forty-eighth
clock. If it is brought HIGH at any other time, the write
operation will not be completed. Refer to Figure 4 and 5
below for a detailed illustration of the write sequences.
While the write is in progress, following a status register
or E
2
PROM write sequence the status register may be
read to check the WIP bit. During this time the WIP bit will
be HIGH and all other bits in the status register will be
undefined.
RESET
/RESET Operation
The
RESET
(X25043) output is designed to go LOW
whenever V
CC
has dropped below the minimum trip
point and/or the Watchdog timer has reached its pro-
grammable time-out limit.
Table 1. Instruction Set
Instruction Name
WREN
WRDI
RDSR
WRSR
Instruction Format*
0000 0110
0000 0100
0000 0101
0000 0001
Operation
Set the Write Enable Latch (Enable Write Operations)
Reset the Write Enable Latch (Disable Write Operations)
Read Status Register
Write Status Register (Block Lock Bits)
Read Data from Memory Array beginning at selected
address
Write Data to Memory Array beginning at Selected Address
(1 to 4 Bytes)
READ
0000 A
8
011
WRITE
0000 A
8
010
3844 PGM T05.1
*Instructions are shown MSB in leftmost position. Instructions are transferred MSB first.
相關PDF資料 |
PDF描述 |
|---|---|
| X25043V-2.7 | Programmable Watchdog Supervisory E2PROM |
| X25057V-1.8 | 5MHz Low Power SPI Serial E 2 PROM with IDLock⑩ Memory |
| X25057M-1.8 | 5MHz Low Power SPI Serial E 2 PROM with IDLock⑩ Memory |
| X25057M-2.7 | 5MHz Low Power SPI Serial E 2 PROM with IDLock⑩ Memory |
| X25057S-1.8 | 5MHz Low Power SPI Serial E 2 PROM with IDLock⑩ Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X25043PI-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features |
| X25043S | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Programmable Watchdog Supervisory E2PROM |
| X25043S-2.7 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Programmable Watchdog Supervisory E2PROM |
| X25043S-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM with Supervisory Features |
| X25043SI | 制造商:Intersil Corporation 功能描述:Serial EEPROM, 512 x 8, 8 Pin, Plastic, SOP |
發布緊急采購，3分鐘左右您將得到回復。