參數資料
型號: X25045VI-2.7
英文描述: Programmable Watchdog Supervisory E2PROM
中文描述: 可編程看門狗監控E2PROM的
文件頁數: 3/15頁
文件大?。?/td> 93K
代理商: X25045VI-2.7
X25043/45
3
PRINCIPLES OF OPERATION
The X25043/45 is a 512 x 8 E
2
PROM designed to
interface directly with the synchronous serial peripheral
interface (SPI) of many popular microcontroller families.
The X25043/45 contains an 8-bit instruction register. It
is accessed via the SI input, with data being clocked in
on the rising SCK.
CS
must be LOW and
WP
input must
be HIGH during the entire operation. The X25043/45
monitors the bus and provides a
RESET
/RESET output
if there is no bus activity within the preset time period.
Table 1 contains a list of the instructions and their
operation codes. All instructions, addresses and data
are transferred MSB first. Bit 3 of the Read and Write
instructions contain the higher order address bit, A
8
.
Data input is sampled on the first rising edge of SCK after
CS
goes LOW. SCK is static, allowing the user to stop
the clock and then resume operations.
Write Enable Latch
The X25043/45 contains a “write enable” latch. This
latch must be SET before a write operation will be
completed internally. The WREN instruction will set the
latch and the WRDI instruction will reset the latch. This
latch is automatically reset upon a power-up condition
and after the completion of a byte, page, or status
register write cycle. The latch is also reset if
WP
is
brought LOW.
Status Register
The RDSR instruction provides access to the status
register. The status register may be read at any time,
even during a write cycle. The status register is format-
ted as follows:
7
X
6
X
5
4
3
2
1
0
WD1 WD0
BL1
BL0
WEL
WIP
3844 PGM T02
When issuing, WREN, WRDI and RDSR commands, it
is not necessary to send a byte address or data.
The Write-In-Process (WIP) bit indicates whether the
X25043/45 is busy with a write operation. When set to a
“1”, a write is in progress, when set to a “0”, no write is
in progress. During a write, all other bits are set to “1”.
The WIP bit is read-only.
The Write Enable Latch (WEL) bit indicates the status of
the “write enable” latch. When set to a “1”, the latch is set,
when set to a “0”, the latch is reset. The WEL bit is read-
only and is set by the WREN instruction and reset by
WRDI instruction or successful completion of a write
cycle.
The Block Protect (BL0 and BL1) bits indicate the extent
of protection employed. These nonvolatile bits are set by
issuing the WRSR instruction and allows the user to
select one of four levels of protection and program the
watchdog timer. The X25043/45 is divided into four
1024-bit segments. One, two, or all four of the segments
may be locked. That is, the user may read the segments
but will be unable to alter (write) data within the selected
segments. The partitioning is controlled as illustrated
below with the state of BL1 and BL0.
Status Register Bits
BL1
Array Addresses
Protected
BL0
0
0
1
1
0
1
0
1
None
$180–$1FF
$100–$1FF
$000–$1FF
3844 PGM T04
The Watchdog Timer (WD0 and WD1) bits allow setting
of the watchdog time-out function as shown in the table
below. These nonvolatile bits are set by issuing the
WRSR instruction.
Status Register Bits
WD1
Watchdog Time-out
(Typical)
WD0
0
0
1
1
0
1
0
1
1.4 Seconds
600 Milliseconds
200 Milliseconds
Disabled
3844 PGM T03
相關PDF資料
PDF描述
X25043PI Programmable Watchdog Supervisory E2PROM
X25043VI Programmable Watchdog Supervisory E2PROM
X25045P-2.7 Programmable Watchdog Supervisory E2PROM
X25045VI Programmable Watchdog Supervisory E2PROM
X25043 Programmable Watchdog Supervisory E2PROM
相關代理商/技術參數
參數描述
X25057 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:5MHz Low Power SPI Serial E 2 PROM with IDLock⑩ Memory
X25057M 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:5MHz Low Power SPI Serial E 2 PROM with IDLock⑩ Memory
X25057M-1.8 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:5MHz Low Power SPI Serial E2PROM with IDLock⑩ Memory
X25057M-2.7 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:5MHz Low Power SPI Serial E 2 PROM with IDLock⑩ Memory
X25057MG-1.8 制造商:ICMIC 制造商全稱:IC MICROSYSTEMS 功能描述:5MHz Low Power SPI Serial E2PROM with IDLock⑩ Memory