- 您現在的位置：買賣IC網 > PDF目錄371225 > X25F087V-5 SPI SerialFlash with Block Lock TM Protection PDF資料下載
參數資料
| 型號： | X25F087V-5 |
| 英文描述： | SPI SerialFlash with Block Lock TM Protection |
| 中文描述： | 的SPI SerialFlash區塊可鎖定的商標保護 |
| 文件頁數： | 2/13頁 |
| 文件大?。?/td> | 68K |
| 代理商： | X25F087V-5 |
X25F087
2
PIN DESCRIPTIONS
Serial Output (SO)
SO is a push/pull serial data output pin. During a read
cycle, data is shifted out on this pin. Data is clocked out
by the falling edge of the serial clock.
Serial Input (SI)
SI is a serial data input pin. All opcodes, byte addresses,
and data to be programmed to the memory are input on
this pin. Data is latched by the rising edge of the serial
clock.
Serial Clock (SCK)
The Serial Clock controls the serial bus timing for data
input and output. Opcodes, addresses, or data present
on the SI pin are latched on the rising edge of the clock
input, while data on the SO pin change after the falling
edge of the clock input.
Chip Select (CS)
When CS is HIGH, the X25F087 is deselected and the
SO output pin is at high impedance and unless a nonvol-
atile write cycle is underway, the X25F087 will be in the
standby power mode. CS LOW enables the X25F087,
placing it in the active power mode. It should be noted
that after power-up, a HIGH to LOW transition on CS is
required prior to the start of any operation.
Program Protect (PP)
When PP is LOW, nonvolatile writes to the X25F087 are
disabled, but the part otherwise functions normally. When
PP is held HIGH, all functions, including nonvolatile
writes, operate normally. PP going LOW while CS is still
LOW will interrupt a programming cycle to the X25F087.
If the nonvolatile write cycle has already been initiated,
PP going low will have no affect on this cycle.
PIN CONFIGURATION
PIN NAMES
7007 FRM T01
PRINCIPLES OF OPERATION
The X25F087 is a 1024 x 8 SerialFlash designed to inter-
face directly with the synchronous Serial Peripheral Inter-
face (SPI) of many popular microcontroller families.
The X25F087 contains an 8-bit instruction register. It is
accessed via the SI input, with data being clocked in on
the rising edge of SCK. CS must be LOW and the PP
input must be HIGH during the entire operation. Table 1
contains a list of the instructions and their opcodes. All
instructions, addresses and data are transferred MSB first.
Data input is sampled on the first rising edge of SCK
after CS goes LOW. SCK is static, allowing the user to
stop the clock and then start it again to resume opera-
tions where left off.
Program Enable Latch
The X25F087 contains a “Program Enable” latch. This
latch must be SET before a program operation is initi-
ated. The PREN instruction will set the latch and the
PRDI instruction will reset the latch (Figure 4). This latch
is automatically reset upon a power-up condition and
after the completion of a sector program cycle.
Block Lock Protection
There are eight Block Lock Protection options. The pre-
defined blocks and associated address ranges are pro-
tected by programming the appropriate two byte
Program Status instruction to the device (Table 1 and
Figure 6). Once a Block Lock protect instruction has
been completed, that Block Lock Protection setup is held
in a nonvolatile Status Register (Figure 1) until the next
Program Status instruction is issued. The sections of the
memory array that are Block Lock protected can be read
but not programmed until Block Lock Protection is
removed or changed.
SCK
SI
VSS
PP
NC
VCC
CS
SO
1
2
3
4
8
7
6
5
8 PINTSSOP
VCC
NC
SCK
SI
7007 FRM 02
CS
SO
PP
VSS
1
2
3
4
8
7
6
5
8 PIN SOIC/DIP
X25F087
X25F087
*0.197"
*0.244"
0.122"
0.252"
Not to scale
*SOIC Measurement
Symbol
CS
SO
SI
SCK
PP
V
SS
V
CC
NC
Description
Chip Select Input
Serial Output
Serial Input
Serial Clock Input
Program Protect Input
Ground
Supply Voltage
No Connect
相關PDF資料 |
PDF描述 |
|---|---|
| X25F087VI | SPI SerialFlash with Block Lock TM Protection |
| X25F128P-5 | SerialFlash⑩ Memory With Block Lock⑩ Protection |
| X25F128SI-5 | SerialFlash⑩ Memory With Block Lock⑩ Protection |
| X25F128P | SerialFlash⑩ Memory With Block Lock⑩ Protection |
| X25F128PE | SerialFlash⑩ Memory With Block Lock⑩ Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X25F087VI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SPI SerialFlash with Block Lock TM Protection |
| X25F087VI-5 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SPI SerialFlash with Block Lock TM Protection |
| X25F128 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SerialFlash⑩ Memory With Block Lock⑩ Protection |
| X25F128P | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SerialFlash⑩ Memory With Block Lock⑩ Protection |
| X25F128P-5 | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:SerialFlash⑩ Memory With Block Lock⑩ Protection |
發布緊急采購，3分鐘左右您將得到回復。