- 您現在的位置：買賣IC網 > PDF目錄297797 > X40420S14-A 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 PDF資料下載
參數資料
| 型號： | X40420S14-A |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| 封裝： | PLASTIC, SOIC-14 |
| 文件頁數： | 21/25頁 |
| 文件大小： | 547K |
| 代理商： | X40420S14-A |
X40420/X40421
Characteristics subject to change without notice.
5 of 25
REV 1.2.15 2/11/04
www.xicor.com
Figure 4. Watchdog Restart
V1 AND V2 THRESHOLD PROGRAM PROCEDURE
(OPTIONAL)
The X40420/21 is shipped with standard V1 and V2
threshold (VTRIP1, VTRIP2) voltages. These values will not
change over normal operating and storage conditions.
However, in applications where the standard thresholds
are not exactly right, or if higher precision is needed in the
threshold value, the X40420 trip points may be adjusted.
The procedure is described below, and uses the applica-
tion of a high voltage control signal.
Setting a VTRIPx Voltage (x=1, 2)
There are two procedures used to set the threshold volt-
ages (VTRIPx), depending if the threshold voltage to be
stored is higher or lower than the present value. For
example, if the present VTRIPx is 2.9 V and the new
VTRIPx is 3.2 V, the new voltage can be stored directly
into the VTRIPx cell. If however, the new setting is to be
lower than the present setting, then it is necessary to
“reset” the VTRIPx voltage before setting the new value.
Setting a Higher VTRIPx Voltage (x=1, 2)
To set a VTRIPx threshold to a new voltage which is higher
than the present threshold, the user must apply the
desired VTRIPx threshold voltage to the corresponding
input pin (Vcc(V1MON) or V2MON). Then, a program-
ming voltage (Vp) must be applied to the WDO pin before
a START condition is set up on SDA. Next, issue on the
SDA pin the Slave Address A0h, followed by the Byte
Address 01h for VTRIP1, and 09h for VTRIP2, and a 00h
Data Byte in order to program VTRIPx. The STOP bit
following a valid write operation initiates the programming
sequence. Pin WDO must then be brought LOW to
complete the operation.
To check if the VTRIPX has been set, set VXMON to a
value slightly greater than VTRIPX (that was previously
set). Slowly ramp down VXMON and observe when the
corresponding outputs (LOWLINE and V2FAIL) switch.
The voltage at which this occurs is the VTRIPX (actual).
CASE A
Now if the desired VTRIPX is greater than the VTRIPX
(actual), then add the difference between VTRIPX
(desired) – VTRIPX (actual) to the original VTRIPX desired.
This is your new VTRIPX that should be applied to
VXMON and the whole sequence should be repeated
again (see Figure 5).
CASE B
Now if the VTRIPX (actual), is higher than the VTRIPX
(desired), perform the reset sequence as described in the
next section. The new VTRIPX voltage to be applied to
VXMON will now be: VTRIPX (desired) – (VTRIPX (actual)
– VTRIPX (desired)).
Note: 1. This operation does not corrupt the memory
array.
2. Set VCC = 5V, when VTRIP2 is being pro-
grammed
Setting a Lower VTRIPx Voltage (x=1, 2)
In order to set VTRIPx to a lower voltage than the
present value, then VTRIPx must rst be “reset” accord-
ing to the procedure described below. Once VTRIPx
has been “reset”, then VTRIPx can be set to the desired
voltage using the procedure described in “Setting a
Higher VTRIPx Voltage”.
SCL
SDA
.6s
1.3s
WDT Reset
Start
Stop
Figure 3. VTRIPX Set/Reset Conditions
VCC/V2MON
VTRIPX
VP
tWC
A0h
0
7
70
7
0
SCL
WDO
SDA
(X = 1, 2)
00h
相關PDF資料 |
PDF描述 |
|---|---|
| X4163S8Z | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X4165V8-2.7 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X4165S8-4.5A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| X5001S8-1.8 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| X5043V14I-2.7A | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40420S14-AT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40420S14-B | 功能描述:IC VOLT MON DUAL SUP/SW 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40420S14-BT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40420S14-C | 功能描述:IC VOLT MON DUAL SUP/SW 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40420S14-CT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。