- 您現在的位置：買賣IC網 > PDF目錄371252 > X40421V14-B Dual Voltage Monitor with Intergrated CPU Supervisor PDF資料下載
參數資料
| 型號： | X40421V14-B |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Dual Voltage Monitor with Intergrated CPU Supervisor |
| 中文描述： | 雙電壓監視器集成CPU監控 |
| 文件頁數： | 13/25頁 |
| 文件大?。?/td> | 156K |
| 代理商： | X40421V14-B |
S
t
a
r
t
X40420/X40421 – Preliminary
Characteristics subject to change without notice.
13 of 25
REV 1.2.14 7/12/02
www.xicor.com
A similar operation called “Set Current Address” where
the device will perform this operation if a stop is issued
instead of the second start shown in Figure 15. The
device will go into standby mode after the stop and all
bus activity will be ignored until a start is detected. This
operation loads the new address into the address
counter. The next Current Address Read operation will
read from the newly loaded address. This operation
could be useful if the master knows the next address it
needs to read, but is not ready for the data.
Sequential Read
Sequential reads can be initiated as either a current
address read or random address read. The first Data
Byte is transmitted as with the other modes; however,
the master now responds with an acknowledge, indicat-
ing it requires additional data. The device continues to
output data for each acknowledge received. The master
terminates the read operation by not responding with an
acknowledge and then issuing a stop condition.
The data output is sequential, with the data from
address n followed by the data from address n + 1. The
address counter for read operations increments through
all page and column addresses, allowing the entire
memory contents to be serially read during one opera-
tion. At the end of the address space the counter “rolls
over” to address 0000
H
and the device continues to out-
put data for each acknowledge received. See Figure 17
for the acknowledge and data transfer sequence.
SERIAL DEVICE ADDRESSING
Memory Address Map
CR, Control Register, CR7: CR0
Address: 1FF
hex
FDR, Fault DetectionRegister, FDR7: FDR0
Address: 0FF
hex
General Purpose Memory Organization, A8:A0
Address: 00h to 1FFh
General Purpose Memory Array Configuration
Slave Address Byte
Following a start condition, the master must output a
Slave Address Byte. This byte consists of several parts:
– a device type identifier that is always “1010” when
accessing the array and “1011” when accessing the
control register and fault detection register.
– two bits of “0”.
– one bit that becomes the MSB of the memory
address X
4
.
– last bit of the slave command byte is a R/W bit. The
R/W bit of the Slave Address Byte defines the opera-
tion to be performed. When the R/W bit is a one, then
a read operation is selected. A zero selects a write
operation. See Figure 16.
Memory Address
A8:A0
000h
0FFh
100h
1FFh
Lower 256 bytes
Upper 256 bytes
Block Protect Option
Figure 14. Current Address Read Sequence
.
S
t
o
p
Slave
Address
Data
SDA Bus
Signals from
the Slave
Signals from
the Master
1
A
C
K
1 0 1
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| X40421V14-C | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40421V14I-A | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40421V14I-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40421V14I-C | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14-A | Dual Voltage Monitor with Intergrated CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40421V14-BT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40421V14-C | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40421V14-CT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40421V14I-A | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40421V14I-AT1 | 功能描述:IC VOLT MON DUAL SUP/SW 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。